How to Do Ceramic Sculpture
Decide how you want to create your sculpture so it looks good., Hollow out your sculpture., Keep your creation uniform to prevent shrinkage and cracking., Use plastic sheets and bags to keep the work wet while building, and to control drying speed...
Step-by-Step Guide
-
Step 1: Decide how you want to create your sculpture so it looks good.
Sculpture can be created by piecing together things thrown on the wheel, by the use of coils and slabs, using a mold, by making solid objects out of clay, or any combination thereof. -
Step 2: Hollow out your sculpture.
Clay cannot be fired solid, and should only be usually no more than 1⁄2 inch (1.3 cm) thick in any place.
You can use ceramic trimming tools to scrape and dig out the clay while still retaining a strong wall. , Different thickness of clay will shrink at different rates, so most parts of a single piece should be of roughly the same thickness. , Water can be added at any time with various sizes of sponges.
Red iron clay tends to dry slower, have a lot of strength, and is very workable. , Dried, reused clay soaked and dissolved in water can be used as adhesive for attaching parts.
For instance, use a wide-mouth gallon size plastic jar as a base mold and let water evaporate and clay congeal to a thick, axle-grease consistency.
This may take a few weeks.
The adhesive clay is then applied to both ends after scoring and is pressed together.
With a wooden tool, the edges are mashed together both inside and out, then covered with stiff working clay for strength.
When the piece is reassembled, all exterior joints are contoured for the final finish.
This is then dried slowly, the bigger and thicker pieces taking up to two or three weeks.
If the hollowed walls are done unevenly, with curved trimming tools leaving lots of ribbing, the pieces may warp and not end up being smooth. , When joining coils lengthwise for pots, they can be scored and applied together with adhesive clay.
However, the inside should normally be mashed together for strength.
Coils are especially vulnerable to separation on the bottom. , For even rolling, line the clay between two strips of material such as plywood, the thickness of which is the same as with the intended slab.
The ends of the rolling pin, when rolled on the strips, should then flatten the clay to that exact width.
Slabs will tend to considerably warp in the fire.
Interior ceramic bracing may be necessary to mute this.
Plaster used as a working surface will tend to dry out the clay.
Find a non-stick surface such as raw wood. ,, Ceramic sculpture can be glazed, painted with stains, or fired and then painted with acrylics or oils or any combination thereof.
Sculpture too big for the kiln can made in pieces to be fitted together after firing.
Allowance must be made for attachment in the interior and the ability to cover and color the cracks so they do not show.
Ceramic sculpture is delicate and subject to breakage. -
Step 3: Keep your creation uniform to prevent shrinkage and cracking.
-
Step 4: Use plastic sheets and bags to keep the work wet while building
-
Step 5: and to control drying speed.
-
Step 6: Reassemble individual pieces by scoring both ends of reattached pieces and using adhesive mud.
-
Step 7: Roll out coils with fingers
-
Step 8: usually starting from the center and working both hands away from each other.
-
Step 9: Roll out slabs with a rolling pin.
-
Step 10: Create texture in innumerable ways such as rolling clay on burlap
-
Step 11: branding with all sorts of implements
-
Step 12: carving
-
Step 13: using imprint tools.
-
Step 14: Finish the piece.
Detailed Guide
Sculpture can be created by piecing together things thrown on the wheel, by the use of coils and slabs, using a mold, by making solid objects out of clay, or any combination thereof.
Clay cannot be fired solid, and should only be usually no more than 1⁄2 inch (1.3 cm) thick in any place.
You can use ceramic trimming tools to scrape and dig out the clay while still retaining a strong wall. , Different thickness of clay will shrink at different rates, so most parts of a single piece should be of roughly the same thickness. , Water can be added at any time with various sizes of sponges.
Red iron clay tends to dry slower, have a lot of strength, and is very workable. , Dried, reused clay soaked and dissolved in water can be used as adhesive for attaching parts.
For instance, use a wide-mouth gallon size plastic jar as a base mold and let water evaporate and clay congeal to a thick, axle-grease consistency.
This may take a few weeks.
The adhesive clay is then applied to both ends after scoring and is pressed together.
With a wooden tool, the edges are mashed together both inside and out, then covered with stiff working clay for strength.
When the piece is reassembled, all exterior joints are contoured for the final finish.
This is then dried slowly, the bigger and thicker pieces taking up to two or three weeks.
If the hollowed walls are done unevenly, with curved trimming tools leaving lots of ribbing, the pieces may warp and not end up being smooth. , When joining coils lengthwise for pots, they can be scored and applied together with adhesive clay.
However, the inside should normally be mashed together for strength.
Coils are especially vulnerable to separation on the bottom. , For even rolling, line the clay between two strips of material such as plywood, the thickness of which is the same as with the intended slab.
The ends of the rolling pin, when rolled on the strips, should then flatten the clay to that exact width.
Slabs will tend to considerably warp in the fire.
Interior ceramic bracing may be necessary to mute this.
Plaster used as a working surface will tend to dry out the clay.
Find a non-stick surface such as raw wood. ,, Ceramic sculpture can be glazed, painted with stains, or fired and then painted with acrylics or oils or any combination thereof.
Sculpture too big for the kiln can made in pieces to be fitted together after firing.
Allowance must be made for attachment in the interior and the ability to cover and color the cracks so they do not show.
Ceramic sculpture is delicate and subject to breakage.
About the Author
Jack Ford
Specializes in breaking down complex creative arts topics into simple steps.
Rate This Guide
How helpful was this guide? Click to rate: