How to Thread Pipe
Purchase or rent a manual pipe threader machine from an equipment retailer., Inspect the pipe threader before beginning and replace dies or any parts that show signs of wear., Mount your pipe firmly in the pipe vise by placing it in the vise and...
Step-by-Step Guide
-
Step 1: Purchase or rent a manual pipe threader machine from an equipment retailer.
A die head will be attached to cut the thread.
Machines now have the ability to thread pipes made of different material, including various types of plastic or resin.
A heavy duty pipe threader can also cut your pipe into workable sections.
The pipe threading machine will be used to thread the end section of your pipe. -
Step 2: Inspect the pipe threader before beginning and replace dies or any parts that show signs of wear.
Inspection for signs of wear will not be necessary if you purchase a new threader.
Worn or damaged dies can result in poor thread quality. ,, If you have an industrial pipe threader with cutting capability, use the machine to cut your pipe to length.
Pipe cutters come with and without guides, which provide square alignment.
It's better to use a guide, rather than estimating your cut.
The pipe cutter will have a thin cutter wheel, which will slice through the pipe as you guide it in the space.
Be sure to wear goggles and protective gear.
Steel may produce sparks. ,, Die heads come in different shapes and sizes that include different threads for pipes that have different diameters. ,, Before placing too much pressure on the handle, check to be sure the ratchet pawl is engaged. , Be sure to maintain proper footing and balance for maximum control.
Never use a tool or mechanism to hold the handle in place in order to free your hands.
This can be dangerous and could result in injury. , Using an oil too thin as a substitute for threading oil can result in sub-standard threading. , When the die is even with the pipe, that means the correct threading size has been reached.
If you continue pushing after this point, you will damage the thread. , Be careful to maintain control of the threader as the dies are removed.
Threads can become damaged when the die head is being removed if you don't maintain control and move the piece smoothly. ,, Be careful, the threads will be very sharp. ,, -
Step 3: Mount your pipe firmly in the pipe vise by placing it in the vise and then tightening until it is held tightly.
-
Step 4: Cut the end of the pipe cleanly and squarely by using a pipe cutter.
-
Step 5: Ream the cut end of the pipe to remove any burrs from the cut using a reamer
-
Step 6: which is a cylinder-shaped rotary cutting tool that you run smoothly across the freshly cut edges of the pipe to remove rough edges.
-
Step 7: Select your die head according to the size and type of pipe you are threading and the thread form you require.
-
Step 8: Place the die head over the pipe on the threader.
-
Step 9: Press steadily on the front of the die head
-
Step 10: while simultaneously pushing the handle down to start the threader.
-
Step 11: Use your weight as leverage to apply pressure on the handle
-
Step 12: while holding it firmly.
-
Step 13: Apply threading oil generously while threading.
-
Step 14: Cease threading when the end of the threading die is flat against the end of the pipe.
-
Step 15: Reverse the ratchet mechanism and turn the die head in the opposite direction.
-
Step 16: Stand the pipe on end and gently tap it to remove any particles that may be lodged within.
-
Step 17: Clean the pipe with a cloth
-
Step 18: removing any oil.
-
Step 19: Seal the threading with Teflon tape or a pipe thread compound when attaching the pipe to the connector.
-
Step 20: Clean the pipe threader machine thoroughly after use so the oils and metal pieces do not damage the machine
-
Step 21: which could cause sub-standard threading during your next project.
Detailed Guide
A die head will be attached to cut the thread.
Machines now have the ability to thread pipes made of different material, including various types of plastic or resin.
A heavy duty pipe threader can also cut your pipe into workable sections.
The pipe threading machine will be used to thread the end section of your pipe.
Inspection for signs of wear will not be necessary if you purchase a new threader.
Worn or damaged dies can result in poor thread quality. ,, If you have an industrial pipe threader with cutting capability, use the machine to cut your pipe to length.
Pipe cutters come with and without guides, which provide square alignment.
It's better to use a guide, rather than estimating your cut.
The pipe cutter will have a thin cutter wheel, which will slice through the pipe as you guide it in the space.
Be sure to wear goggles and protective gear.
Steel may produce sparks. ,, Die heads come in different shapes and sizes that include different threads for pipes that have different diameters. ,, Before placing too much pressure on the handle, check to be sure the ratchet pawl is engaged. , Be sure to maintain proper footing and balance for maximum control.
Never use a tool or mechanism to hold the handle in place in order to free your hands.
This can be dangerous and could result in injury. , Using an oil too thin as a substitute for threading oil can result in sub-standard threading. , When the die is even with the pipe, that means the correct threading size has been reached.
If you continue pushing after this point, you will damage the thread. , Be careful to maintain control of the threader as the dies are removed.
Threads can become damaged when the die head is being removed if you don't maintain control and move the piece smoothly. ,, Be careful, the threads will be very sharp. ,,
About the Author
Evelyn Campbell
Creates helpful guides on pet care to inspire and educate readers.
Rate This Guide
How helpful was this guide? Click to rate: