How to Build a Retaining Wall
Plan and layout the site., Excavate the site., Tamp the soil level and lay down a paver base., Begin by laying the foundation., Start at the most visible edge of the wall, adding gravel or crushed rock to level the stone, if necessary., If...
Step-by-Step Guide
-
Step 1: Plan and layout the site.
Plan where your retaining wall is going to be using stakes and string, leveling off to ensure an even height and using a tape measure to ensure an even length.
Contact your local utilities office to confirm that there are no pipes or cables in your digging zone.
Your local utilities office should perform this free of charge.
If you live in the USA, you must make an 811 “Digline” call and set up a time to have your property inspected to determine the location of underground utility pipes and cables before starting any digging project.
This is required by law.
Make the call at least a few days before you plan to start your project.
If you want more of a random outline, lay out a line for your wall using a garden hose.
Simply drape the garden hose out in the general area of the proposed wall utilizing its curves.
Check to see that the shape is buildable and aesthetically pleasing, and then use landscaping paint or flour to mark the ground where the garden hose was. -
Step 2: Excavate the site.
Using a shovel, dig a trench along the line you have laid out.
It should be slightly wider than the blocks you will use for your wall.
Check that the trench is as level as possible.
If you live in the USA, you must wait until the Digline locate process is complete before you begin excavating.
Enough space should be made to bury the bottom row of blocks at least 1 inch (2.54 cm) for every 8 inches (20.32 cm) of wall height.
Factor into this equation a level of paver base that will rest on the bottom of the trench. , Using a soil tamper — you can easily rent one for less than $20 — tamp (pack) down the bottom of the trench.
Then, add 4 to 6 inches (10.16-15.24 cm) of patio paver base or rock dust to the bottom of the trench.
Patio paver base is ideal because it is specially made gravel that compacts well and is sturdy.
Rake the paver base once it's been applied, getting as much uniform coverage as possible.
Go over the paver base one more time with a level, making sure that the trench area is a uniform height.
If there's uneven distribution add a little more or take away some paver base by raking.
Tamp the bottom of the trench again, compacting the base a final time. , These are the most critical blocks in your wall.
If they aren't level or adequately support the top half of your retaining wall, the whole project is going to look less than professional.
Make sure that the foundational blocks are leveled off, sturdy, and tightly packed together. , Add the first block to the trench, using a cornerstone.
Make sure it is level from front to back and side to side.
Alternately, if there's no edge to the wall that is more visible than another, start at the edge that will be closest to another structure (usually a house).
If you're building a straight or rectangular retaining wall, make sure that the backs of the blocks line up with one another perfectly; if you're building a curved retaining wall, make sure that the fronts of the blocks line up with one another perfectly. , Some contractors prefer cutting off the top tongue or groove from the base stones before laying them down.
Check for sturdiness yourself and knock the tongue off the block with a hammer and chisel, if necessary.
Understand that curved retaining walls with tongues may not benefit from the interlocking grooves.
These grooves will need to be cut off with a hammer and chisel if the layout of the pattern does not fit the direction of the grooves. , If you took the time to level off the bed, laying the first row should be easy.
Use coarse sand where necessary to get a level finish on your foundation.
Hammer the blocks down with your rubber mallet. , Always use proper protection when cutting. , This will provide excellent support, keeping your bottom layer from slipping back with time and erosion. , This will prevent frost heave and keeps the soil from mixing with the backfill.
Depending on how tall your retaining wall is, you may want to drape the filler along the back side of the trench or house, fill the trench with backfill until it's anchored the filter fabric down, and then drape the fabric flat out, on top of the backfill. ,, You want each layer of blocks to be different from the one below it.
For example, if the wall has straight edges on the ends, the next layer should start with a block that has been cut in half.
Place the blocks onto the foundation before applying the adhesive.
See how they look; ask yourself whether you need to make any significant cuts before gluing .
Lay out one whole row before moving on to the next step.
If you're working with blocks that have flanged tongues, simply line up the female groove of the top block with the male groove of the bottom block. , Press down to make sure that each layer is secured tightly against the layer beneath it.
Continue until retaining wall is its preferred height.
If your wall is over 3 ft (.91 m) in height, you should offset each new row slightly back from the row below it, like very shallow stair steps.
This will make your wall more stable and help create a better hold with the soil once you backfill. , Look for a perforated pipe and lay it down the length of the retaining wall, covering it up with breathable backfill.
Make sure water can drain out of your pipe, either at the ends or through an outlet in the middle of the wall. , Topper stones usually come in rectangular shapes, making them more difficult to install in curved retaining walls.
If you need to cut topper stones to fit the curve in your retaining wall, follow this trick:
Lay stones #1 and #3 out in their pattern.
Lay stone #2 on top of #1 and #3, drawing lines on #1 and #3 where stone #2 overlaps them.
Cut stones #1 and #3 along those lines.
Line up #1 and #3 into place, snugging #2 in between.
Repeat, placing stone #4 on top of stones #3 and #5. , Add plants, vines, or flowers as necessary.
Your retaining wall is ready to be enjoyed. -
Step 3: Tamp the soil level and lay down a paver base.
-
Step 4: Begin by laying the foundation.
-
Step 5: Start at the most visible edge of the wall
-
Step 6: adding gravel or crushed rock to level the stone
-
Step 7: if necessary.
-
Step 8: If necessary
-
Step 9: cut off the top tongue of the base stones.
-
Step 10: Use coarse sand and a rubber mallet to level off the first layer of blocks
-
Step 11: completing the entire foundation.
-
Step 12: If necessary
-
Step 13: cut individual blocks to complete the first layer by simply marking them at the appropriate length and cutting with a mason's saw.
-
Step 14: Use crushed stone or gravel for backfill on your first layer of blocks.
-
Step 15: Place a filter fabric over the backfill.
-
Step 16: Sweep the first layer with a broom to free up any dirt or dust.
-
Step 17: Start your second layer with a staggered pattern
-
Step 18: so that the top layer seams are offset with the bottom layer.
-
Step 19: Once a layer has been provisionally laid out
-
Step 20: apply the recommended adhesive to the bottom blocks and fit the top block overhead.
-
Step 21: Add drainage pipes to your retaining wall if the wall is 2 feet (60 cm) or taller.
-
Step 22: Add topper stones if you desire them.
-
Step 23: Place topsoil in the basin created by the retaining wall.
Detailed Guide
Plan where your retaining wall is going to be using stakes and string, leveling off to ensure an even height and using a tape measure to ensure an even length.
Contact your local utilities office to confirm that there are no pipes or cables in your digging zone.
Your local utilities office should perform this free of charge.
If you live in the USA, you must make an 811 “Digline” call and set up a time to have your property inspected to determine the location of underground utility pipes and cables before starting any digging project.
This is required by law.
Make the call at least a few days before you plan to start your project.
If you want more of a random outline, lay out a line for your wall using a garden hose.
Simply drape the garden hose out in the general area of the proposed wall utilizing its curves.
Check to see that the shape is buildable and aesthetically pleasing, and then use landscaping paint or flour to mark the ground where the garden hose was.
Using a shovel, dig a trench along the line you have laid out.
It should be slightly wider than the blocks you will use for your wall.
Check that the trench is as level as possible.
If you live in the USA, you must wait until the Digline locate process is complete before you begin excavating.
Enough space should be made to bury the bottom row of blocks at least 1 inch (2.54 cm) for every 8 inches (20.32 cm) of wall height.
Factor into this equation a level of paver base that will rest on the bottom of the trench. , Using a soil tamper — you can easily rent one for less than $20 — tamp (pack) down the bottom of the trench.
Then, add 4 to 6 inches (10.16-15.24 cm) of patio paver base or rock dust to the bottom of the trench.
Patio paver base is ideal because it is specially made gravel that compacts well and is sturdy.
Rake the paver base once it's been applied, getting as much uniform coverage as possible.
Go over the paver base one more time with a level, making sure that the trench area is a uniform height.
If there's uneven distribution add a little more or take away some paver base by raking.
Tamp the bottom of the trench again, compacting the base a final time. , These are the most critical blocks in your wall.
If they aren't level or adequately support the top half of your retaining wall, the whole project is going to look less than professional.
Make sure that the foundational blocks are leveled off, sturdy, and tightly packed together. , Add the first block to the trench, using a cornerstone.
Make sure it is level from front to back and side to side.
Alternately, if there's no edge to the wall that is more visible than another, start at the edge that will be closest to another structure (usually a house).
If you're building a straight or rectangular retaining wall, make sure that the backs of the blocks line up with one another perfectly; if you're building a curved retaining wall, make sure that the fronts of the blocks line up with one another perfectly. , Some contractors prefer cutting off the top tongue or groove from the base stones before laying them down.
Check for sturdiness yourself and knock the tongue off the block with a hammer and chisel, if necessary.
Understand that curved retaining walls with tongues may not benefit from the interlocking grooves.
These grooves will need to be cut off with a hammer and chisel if the layout of the pattern does not fit the direction of the grooves. , If you took the time to level off the bed, laying the first row should be easy.
Use coarse sand where necessary to get a level finish on your foundation.
Hammer the blocks down with your rubber mallet. , Always use proper protection when cutting. , This will provide excellent support, keeping your bottom layer from slipping back with time and erosion. , This will prevent frost heave and keeps the soil from mixing with the backfill.
Depending on how tall your retaining wall is, you may want to drape the filler along the back side of the trench or house, fill the trench with backfill until it's anchored the filter fabric down, and then drape the fabric flat out, on top of the backfill. ,, You want each layer of blocks to be different from the one below it.
For example, if the wall has straight edges on the ends, the next layer should start with a block that has been cut in half.
Place the blocks onto the foundation before applying the adhesive.
See how they look; ask yourself whether you need to make any significant cuts before gluing .
Lay out one whole row before moving on to the next step.
If you're working with blocks that have flanged tongues, simply line up the female groove of the top block with the male groove of the bottom block. , Press down to make sure that each layer is secured tightly against the layer beneath it.
Continue until retaining wall is its preferred height.
If your wall is over 3 ft (.91 m) in height, you should offset each new row slightly back from the row below it, like very shallow stair steps.
This will make your wall more stable and help create a better hold with the soil once you backfill. , Look for a perforated pipe and lay it down the length of the retaining wall, covering it up with breathable backfill.
Make sure water can drain out of your pipe, either at the ends or through an outlet in the middle of the wall. , Topper stones usually come in rectangular shapes, making them more difficult to install in curved retaining walls.
If you need to cut topper stones to fit the curve in your retaining wall, follow this trick:
Lay stones #1 and #3 out in their pattern.
Lay stone #2 on top of #1 and #3, drawing lines on #1 and #3 where stone #2 overlaps them.
Cut stones #1 and #3 along those lines.
Line up #1 and #3 into place, snugging #2 in between.
Repeat, placing stone #4 on top of stones #3 and #5. , Add plants, vines, or flowers as necessary.
Your retaining wall is ready to be enjoyed.
About the Author
Teresa Kim
Enthusiastic about teaching DIY projects techniques through clear, step-by-step guides.
Rate This Guide
How helpful was this guide? Click to rate: