How to Fix Noisy Brakes
Check for loose parts., Replace any shims or clips that are loose, damaged or missing to ensure that the pad does not move in the caliper assembly. , Try a dampening paste., Check the brake pads, and replace them if they are worn., Try different...
Step-by-Step Guide
-
Step 1: Check for loose parts.
Try wiggling the brake pad, calipers, and other brake components.
They should not move with just your hands.Loose parts can vibrate, resulting in noise. -
Step 2: Replace any shims or clips that are loose
, Disc Brake Quiet is one brand.
Apply a thin layer of the substance to the back of the brake pads (between the pad and the caliper assembly).
This will create a thin cushion to dampen the vibration and thereby the sound.
Give the paste plenty of time to dry before you assemble the brakes to make sure it hardens: two to three hours at least, overnight if you can.
It will become sticky and change to a darker color when it is dry.
Heat from the sun or a hair dryer helps to dry the paste, but let it cool to room temperature before installing the pads.
Should you need to clean or remove the dampening paste, use a degreaser or brake cleaner. , Many disc brakes include a wear indicator designed to make noise if the pad is worn past a certain point.With aftermarket pads, sometimes the sizes can vary and cause the top of the pad to sit just slightly higher than the rotor.
This will result in the brake pad wearing unevenly, leaving a lip or kind of a shelf of brake pad that rides over the tip of the rotor.
This causes the brake pad to ride the edge of the rotor, causing a rotational brake noise.
If your brake pads still have plenty of life left in them, you can sand the lip of the pad down (make sure you wear a mask to protect your lungs) to get more life out of the existing pads and eliminate the noise. , Try different materials, but remember that noise and effectiveness may be a trade-off.
It is best to replace brake pads with a similar material.
Check the service manual for your vehicle to see what the manufacturer recommends.
An organic pad (with or without asbestos) may be quieter, but may lack the performance and wear resistance of a semi-metallic or metallic pad.
An organic pad may not tolerate heat as well, and may therefore be subject to more brake fade (reduction in braking effectiveness due to heat) than other pad materials.
A semi-metallic pad, which has metal particles and organic material, tends to have the best of both worlds in braking ability without too much noise.
It increases the pad life and decreases brake fade over organics, but it may wear the rotors slightly more.
It will also tolerate repeated, hard stopping better without wearing as much as the organic pad.
A "metallic pad" is just that.
Different metals are used to provide the most friction against the rotor.
It does a great job at stopping at repeated high speeds with minimum wear, but it will tend to make the most noise out of all the pads.
Metallic pads will also cause the rotor to wear faster (grooves, ridges etc.), especially with stock rotors not designed for use with metal pads.
Look for lubricating materials built into brake pads.
Brass, graphite, carbon, and other materials in the formula can help reduce noise.Because these materials are built into the brake pad itself, they will continue to lubricate rather than wearing off upon use. , An irregular brake rotor or drum surface can cause the brake pad to jump and chatter in the brake assembly and caliper.
Check the surface smoothness visually against a comparator gauge or try writing on it with a ball point pen.
If you don't get a smooth line, the rotor is either too greasy or too rough., If the rotor wear is not too deep, you may be able to have the rotors ground on a lathe to smooth the surface.
Call around to find an auto shop that services brakes and has a rotor lathe.
If you do find a shop, ask if they use round lathe bits to refinish as they produce smoother finishes.
Additionally you should put a cross-hatch pattern on the newly cut surface using a rotor hone tool, it's similar to what your do with cylinders bores in an engine block. , If the wear is excessive or if the entire rotor is warped or distorted, you may have to replace the rotors altogether.
Brake systems may be carefully designed and "tuned" by the manufacturer to avoid noise, so it is best to choose as close a replacement as possible.You may also need new rotors if the sound is not a squeal, but a metallic grind.
If the brake pads are too worn, the rotors may be damaged. -
Step 3: damaged or missing to ensure that the pad does not move in the caliper assembly.
-
Step 4: Try a dampening paste.
-
Step 5: Check the brake pads
-
Step 6: and replace them if they are worn.
-
Step 7: Try different brake pad materials.
-
Step 8: Check the brake rotor or drum for scoring
-
Step 9: grooving
-
Step 10: or other wear.
-
Step 11: Resurface the rotors.
-
Step 12: Replace the rotors or drums.
Detailed Guide
Try wiggling the brake pad, calipers, and other brake components.
They should not move with just your hands.Loose parts can vibrate, resulting in noise.
, Disc Brake Quiet is one brand.
Apply a thin layer of the substance to the back of the brake pads (between the pad and the caliper assembly).
This will create a thin cushion to dampen the vibration and thereby the sound.
Give the paste plenty of time to dry before you assemble the brakes to make sure it hardens: two to three hours at least, overnight if you can.
It will become sticky and change to a darker color when it is dry.
Heat from the sun or a hair dryer helps to dry the paste, but let it cool to room temperature before installing the pads.
Should you need to clean or remove the dampening paste, use a degreaser or brake cleaner. , Many disc brakes include a wear indicator designed to make noise if the pad is worn past a certain point.With aftermarket pads, sometimes the sizes can vary and cause the top of the pad to sit just slightly higher than the rotor.
This will result in the brake pad wearing unevenly, leaving a lip or kind of a shelf of brake pad that rides over the tip of the rotor.
This causes the brake pad to ride the edge of the rotor, causing a rotational brake noise.
If your brake pads still have plenty of life left in them, you can sand the lip of the pad down (make sure you wear a mask to protect your lungs) to get more life out of the existing pads and eliminate the noise. , Try different materials, but remember that noise and effectiveness may be a trade-off.
It is best to replace brake pads with a similar material.
Check the service manual for your vehicle to see what the manufacturer recommends.
An organic pad (with or without asbestos) may be quieter, but may lack the performance and wear resistance of a semi-metallic or metallic pad.
An organic pad may not tolerate heat as well, and may therefore be subject to more brake fade (reduction in braking effectiveness due to heat) than other pad materials.
A semi-metallic pad, which has metal particles and organic material, tends to have the best of both worlds in braking ability without too much noise.
It increases the pad life and decreases brake fade over organics, but it may wear the rotors slightly more.
It will also tolerate repeated, hard stopping better without wearing as much as the organic pad.
A "metallic pad" is just that.
Different metals are used to provide the most friction against the rotor.
It does a great job at stopping at repeated high speeds with minimum wear, but it will tend to make the most noise out of all the pads.
Metallic pads will also cause the rotor to wear faster (grooves, ridges etc.), especially with stock rotors not designed for use with metal pads.
Look for lubricating materials built into brake pads.
Brass, graphite, carbon, and other materials in the formula can help reduce noise.Because these materials are built into the brake pad itself, they will continue to lubricate rather than wearing off upon use. , An irregular brake rotor or drum surface can cause the brake pad to jump and chatter in the brake assembly and caliper.
Check the surface smoothness visually against a comparator gauge or try writing on it with a ball point pen.
If you don't get a smooth line, the rotor is either too greasy or too rough., If the rotor wear is not too deep, you may be able to have the rotors ground on a lathe to smooth the surface.
Call around to find an auto shop that services brakes and has a rotor lathe.
If you do find a shop, ask if they use round lathe bits to refinish as they produce smoother finishes.
Additionally you should put a cross-hatch pattern on the newly cut surface using a rotor hone tool, it's similar to what your do with cylinders bores in an engine block. , If the wear is excessive or if the entire rotor is warped or distorted, you may have to replace the rotors altogether.
Brake systems may be carefully designed and "tuned" by the manufacturer to avoid noise, so it is best to choose as close a replacement as possible.You may also need new rotors if the sound is not a squeal, but a metallic grind.
If the brake pads are too worn, the rotors may be damaged.
About the Author
Kevin Clark
Dedicated to helping readers learn new skills in cooking and beyond.
Rate This Guide
How helpful was this guide? Click to rate: