How to Install a Faucet
Gather the right materials., Turn off the water., Disconnect the lines., Remove the nuts., Clean the area., Prepare for the new faucet., Insert the faucet., Lock it in place., Reattach the supply lines with the adjustable wrench., Test your...
Step-by-Step Guide
-
Step 1: Gather the right materials.
Special plumber's tools aren't required, just a few basic tools you may already own.
Have a small bucket to catch residue water and a plastic drop sheet to keep the bottom of the cabinet dry in case of a leak or spill.
Choose a faucet from the hardware store, and follow the manufacturer's instructions.
A basin wrench is useful for this, but standard wrenches or pliers will work just fine.
You will also need clear silicon caulk or plumber's putty and some plumber's tape. -
Step 2: Turn off the water.
The shut off valves are located below the sink.
They are usually oval-shaped and found somewhere below the supply line for the tap.
Turn them (very gently) clockwise to shut off the water.
If a valve seems excessively tight, it may need to be replaced.
Check the condition of the supply lines for leaks or obvious wear.
You may want to replace these at the same time you replace the faucet.
Most new faucets come fully assembled, some even with inlet hoses attached.
Check with the clerk at the hardware store to be sure. , Disconnect the supply lines using a standard wrench.
There should be two: one for the hot water and one for the cold. , Next, remove the mounting nuts from the bottom of the old faucet.
These are usually under the sink and directly below where the faucet meets the counter.
There should be between 1-3 nuts and they will usually look less like a traditional nut and more like a target or clock.
A basin wrench will make this job much easier. , Remove any old caulk or putty around the holes in the sink.
This is most easily done with a putty knife.
Clean the area thoroughly and wipe dry. , Wrap thread seal tape around the threads of the faucet where they connect to the lines.
Apply silicone sealant around the sink holes and where the new deck plate will be. , Press the faucet down through the sink holes.
Align the faucet, using the wall or the back of the sink to keep the faucet straight.
Once this is done, wipe away any excess residue silicone.
Ensure the inside of basin cabinet is dry. , Hand-tighten the mounting nuts with the thicker side up.
Use pliers if necessary to stop leaks, but do not over-tighten.
It may be handy to follow the specific instructions from the manufacturer for your new faucet, as where and how many of these nuts need to be placed will vary between faucet styles. , Plumber's tape can also be handy here.
Look for a label on the lines attached to the faucet, since you want to connect the correct temperatures (hot handle to hot water, etc). , Turn the water on slowly and check for leaks.
If you see any water dripping, turn off the valves and tighten slightly.
Repeat if necessary.
When everything works the way it should, you're done! -
Step 3: Disconnect the lines.
-
Step 4: Remove the nuts.
-
Step 5: Clean the area.
-
Step 6: Prepare for the new faucet.
-
Step 7: Insert the faucet.
-
Step 8: Lock it in place.
-
Step 9: Reattach the supply lines with the adjustable wrench.
-
Step 10: Test your connections.
Detailed Guide
Special plumber's tools aren't required, just a few basic tools you may already own.
Have a small bucket to catch residue water and a plastic drop sheet to keep the bottom of the cabinet dry in case of a leak or spill.
Choose a faucet from the hardware store, and follow the manufacturer's instructions.
A basin wrench is useful for this, but standard wrenches or pliers will work just fine.
You will also need clear silicon caulk or plumber's putty and some plumber's tape.
The shut off valves are located below the sink.
They are usually oval-shaped and found somewhere below the supply line for the tap.
Turn them (very gently) clockwise to shut off the water.
If a valve seems excessively tight, it may need to be replaced.
Check the condition of the supply lines for leaks or obvious wear.
You may want to replace these at the same time you replace the faucet.
Most new faucets come fully assembled, some even with inlet hoses attached.
Check with the clerk at the hardware store to be sure. , Disconnect the supply lines using a standard wrench.
There should be two: one for the hot water and one for the cold. , Next, remove the mounting nuts from the bottom of the old faucet.
These are usually under the sink and directly below where the faucet meets the counter.
There should be between 1-3 nuts and they will usually look less like a traditional nut and more like a target or clock.
A basin wrench will make this job much easier. , Remove any old caulk or putty around the holes in the sink.
This is most easily done with a putty knife.
Clean the area thoroughly and wipe dry. , Wrap thread seal tape around the threads of the faucet where they connect to the lines.
Apply silicone sealant around the sink holes and where the new deck plate will be. , Press the faucet down through the sink holes.
Align the faucet, using the wall or the back of the sink to keep the faucet straight.
Once this is done, wipe away any excess residue silicone.
Ensure the inside of basin cabinet is dry. , Hand-tighten the mounting nuts with the thicker side up.
Use pliers if necessary to stop leaks, but do not over-tighten.
It may be handy to follow the specific instructions from the manufacturer for your new faucet, as where and how many of these nuts need to be placed will vary between faucet styles. , Plumber's tape can also be handy here.
Look for a label on the lines attached to the faucet, since you want to connect the correct temperatures (hot handle to hot water, etc). , Turn the water on slowly and check for leaks.
If you see any water dripping, turn off the valves and tighten slightly.
Repeat if necessary.
When everything works the way it should, you're done!
About the Author
Janet King
Committed to making cooking accessible and understandable for everyone.
Rate This Guide
How helpful was this guide? Click to rate: