How to Install Cement Board Soffit Panels

Step-by-Step Guide

1. 1

   Step 1: Choose the product you wish to install.

   Soffit and ceiling cement board products are available from a number of manufacturers and have a variety of surface finishes.
   
   You can research these at building product retailers, lumber and building supply stores, and larger home improvement warehouses.
   
   Here are some things to consider:
   Dimension.
   
   Sheets can be in various sizes, from 12 inch (30cm) widths to 48 inch (121cm), and in lengths up to twelve feet (3.6 meters).
   
   Thicknesses are available from 1/4 inch to 1/2 inch (6.5mm to
   1.3cm).
   
   Surface.
   
   The surface of these products are available in rough-sawn lumber finish, faux stucco, and smooth.
   
   Perforated or non-perforated.
   
   For ventilated soffit applications, the cement board product is available in perforated sheets, for non-ventilated, solid sheets are available.
2. 2

   Step 2: Determine the framing requirements for the material you choose.

   Cement board requires support at a maximum of two foot (60cm) spacing, and additional blocking may be required at sheet edges to insure the surfaces are flush after installation.
   
   The best results are achieved when blocking is installed at all edge and end joints.
   
   Because of the weight of this material, joists or other framing members must be capable of supporting the total weight after installation. , For ceiling and soffit installation, exterior grade, paintable screws with countersink heads are required by some manufacturers.
   
   These should be able to penetrate the framing member a minimum of four times the thickness of the panel being installed.
   
   If you choose to use nails, hot dipped galvanized or stainless steel siding nails are recommended. , Install all framing members and roofing components to assure the assembly will not be exposed to weather until the installation is complete.,, Allow enough space so that positioning the board can be accomplished without damaging the edges, but make sure any exposed joints will have an acceptable appearance.
   
   Trim or batten strips may be used if joints are not tight enough to offer an acceptable appearance. , There are several methods used for cutting cement board:
   Circular saws.
   
   Special saw blades are available for cutting cement board, but carbide toothed circular saw blades will give satisfactory cuts if the amount of cutting is not excessive.
   
   Avoid breathing the dust produced by sawing, either by using a fan or wearing a NIOSH approved respirator.
   
   Pneumatic or electric sheers can be used for thin boards, but are expensive and usually only practical for a professional installer.
   
   Scoring and snapping.
   
   Using a straightedge and scoring the board with a sharp utility knife, then bending it (similar to cutting gypsum wallboard products) is a technique that can be used––it produces very little dust, but is less precise and doesn't give a smooth, flat cut. , Be very careful if large holes occur, or if holes are very close to the edge of the board, as this can cause breakage if carelessly handled in installation., Screws can be driven through the board without pilot holes, however, if a certain spacing is required, laying out the screw locations and drilling pilot holes will make meeting this requirement simpler, and will make starting the screws easier. , Sheets must be supported carefully, or they will break, and because of the weight of the material, at least two people should be engaged in this step.
   
   If the installers are working from a ladder or scaffold, a ground person may use a piece of lumber to help hold the panel up while the installers position the piece and tack it in place. ,, Install trim and caulk joints as needed, clean up surfaces where blemishes or spoiling from screw penetrations has occurred. ,
3. 3

   Step 3: Choose appropriate fasteners.

4. 4

   Step 4: Gather your supplies

5. 5

   Step 5: including the fasteners

6. 6

   Step 6: caulking

7. 7

   Step 7: ladders or scaffolding

8. 8

   Step 8: screw-guns

9. 9

   Step 9: drills

10. 10

    Step 10: cement board

11. 11

    Step 11: and hand tools.

12. 12

    Step 12: Place the cement board sheets on a flat surface with sufficient supports to keep them from bowing

13. 13

    Step 13: and keep them dry before installation.

14. 14

    Step 14: Measure the width and length of a space you will install a sheet of cement board on.

15. 15

    Step 15: Cut the board to the required width and length.

16. 16

    Step 16: Mark the location of any electrical devices or other items which will penetrate the sheet and cut holes for them.

17. 17

    Step 17: Pre-drill holes for fasteners if desired.

18. 18

    Step 18: Lift the sheet into place.

19. 19

    Step 19: Drive all fasteners into the panel

20. 20

    Step 20: making sure to sink them flush with the surface or slightly below it

21. 21

    Step 21: but be aware it is possible to drive screws too deep

22. 22

    Step 22: causing them to fail.

23. 23

    Step 23: Fit each subsequent sheet or panel into place until the area your are working in is complete.

24. 24

    Step 24: Prime and paint the soffit or ceiling according to manufacturer's recommendations.

Detailed Guide

About the Author