How to Replace a Swimming Pool Pump Seal

Step-by-Step Guide

1. 1

   Step 1: Separate the pump housing - Most pumps have either a large metal clamp ring or a series of nuts and bolts the hold the pump housing to the motor plate.

   Using a socket or crescent wrench, remove the nut that is securing clamp together or loosen and remove the series of nuts and bolts.
   
   Some banded pumps have a hand knob instead of a nut holding the clamp together.
   
   Slide back the half of the pump assembly with the motor attached.
   
   Try to place the pump on a suitable work surface.
   
   Note:
   You can either leave the electrical conduit intact while doing this procedure or if you require more space you can disconnect the wires form the motor.
   
   Be sure the POWER IS OFF and note the wiring so you reattach the wires the same way!
2. 2

   Step 2: Expose the Impeller - Remove the screws from the impeller cover (diffuser).Remove the impeller cover (diffuser).

   Be sure not to lose any of the screws! , The impeller is one of the more likely pump components to develop wear or damage and inspection at this stage can save you the headache of needing to open and repair the pump a second time in the future. , Replace the impeller if it shows any signs of damage. , The use of vice grips to hold the shaft is never recommended.
   
   Instead, remove the cap from the center of the motor on the end opposite the shaft, and use a screwdriver or open-end wrench to prevent the shaft from turning.
   
   Unscrew and remove the impeller. , Usually there will be 4 bolts that hold the seal plate to the motor.
   
   You will need to remove the impeller before you can remove the seal plate. , Inside the center of the seal plate is the ceramic part of the pump seal.
   
   Be careful not to damage the plastic of the seal plate.
   
   You can also push it out from behind instead, using a screwdriver knock out the old ceramic seal.
   
   Note:
   Be sure the rubber ring seat is removed with the ceramic portion also. , Inspect the seal plate for damage, cracks, melted or out of round will cause the pump to leak even with a new seal.
   
   Carefully inspect the impeller for cracks or breaks. , Press the ceramic part of the seal into the seal plate... using clean fingers to get it seated. (The rubber part towards the seal plate, the white ceramic facing away from the motor.)Slide the spring seal part over the motor shaft.
   
   Push it past the threads.( Black carbon face of the spring side needs to make contact with the white ceramic side).Do NOT LUBRICATE this seal with anything besides water! If you do, then it could end up slipping against the impeller, and eventually overheat, destroying the seal. , HAND TIGHT.
   
   The rotation of the pump motor will keep it tight. , Ensure that the impeller does not touch or interfere with the diffuser, by rotating it with you finger. , If it's flattened or stretched out, it may need to be replaced.
   
   Be sure the clamp is 'around' the outside rim on both sides of the seal plate and the pump housing.
   
   This can be a little tricky to get aligned.
   
   Tighten the retaining band with a wrench or socket, or if your pump has a knob, use your hand to tighten it.
   
   If you pump uses nuts and blots reassemble and tighten.
3. 3

   Step 3: At this stage it is very important to inspect the impeller for damage since you have the pool pump open.

4. 4

   Step 4: An impeller can show signs of heat damage and be melted or the leading edge of the impeller fins could be pock marked if the impeller has been exposed to cavitation.

5. 5

   Step 5: Remove the Impeller - You will need to stop the motor shaft from turning while you rotate the impeller counter-clockwise to remove it.

6. 6

   Step 6: Remove the seal plate - Remove the (seal plate) from the motor to gain access to the motor shaft.

7. 7

   Step 7: Remove the old seal assembly - Using a pair of channel-locks

8. 8

   Step 8: pull off the old pump spring seal from the motor shaft.

9. 9

   Step 9: Clean and prepare to replace the seal - Lightly wipe off the motor shaft and the seal plate.

10. 10

    Step 10: Install the new seal assembly - Note: NEVER touch the FACE of the ceramic with anything metallic or greasy

11. 11

    Step 11: because you could destroy the integrity of the pump seal.

12. 12

    Step 12: Replace the Impeller - Using the Vice grip method mentioned previously

13. 13

    Step 13: hold the motor shaft to prevent rotation

14. 14

    Step 14: and then screw on the impeller.

15. 15

    Step 15: Replace the Diffuser - Now realign the diffuser

16. 16

    Step 16: and tighten the screws.

17. 17

    Step 17: Re assemble the pump and motor - Inspect and lube the large seal plate o-ring for cracks or damage.

Detailed Guide

About the Author