How to Clean a Syringe
Clean syringes immediately before and after using them., Prepare your disinfecting area., Wash your hands thoroughly., Fill one small container with bleach and cold water., Draw water into and eject it out of the syringe., Pour water into the...
Step-by-Step Guide
-
Step 1: Clean syringes immediately before and after using them.
This may seem like a troublesome routine.
However, cleaning syringes right before and after using them will greatly reduce the chances of catching a blood borne disease, like hepatitis or HIV.
This will also prevent blood from hardening in the syringe., Kitchens work best for cleaning syringes, though bathrooms are also suitable in a pinch.
Clean the entire area where you’ll be disinfecting syringes thoroughly with a strong cleaner, like bleach.
Avoid disinfecting syringes in dirty areas.
Doing so could result in your bacteria or viruses being transferred from the work area to disinfected syringes., Wet your hands in cool water.
Apply a household soap to them.
Rub your hands together to lather up the soap.
Pay close attention to the spaces between your fingers and your fingernails.
Bacteria often hides in these places.
Rinse the soap from your hands with cool water.
Wash your hands for at least 20 seconds.
A quick rinse will not effectively remove germs from your hands., If you don’t have suitable containers, use a clean cap or cup.
The containers should be large enough to hold at least a full syringe of fluid.
If your sink is flat bottomed, you may want to place these containers in the sink in case of spillage.
If you don’t have bleach, fill the container with high percentage isopropyl alcohol (90% or higher recommended) or hydrogen peroxide., Place the tip of your needle in the water.
Draw back the plunger to fill the barrel of the syringe.
Lightly shake the syringe.
Position the needle over the drain and press the plunger to eject the water.
Do this several times.
Never reuse fluid that has been inside a syringe.
Fluid used to rinse or disinfect syringes should be disposed down a drain.Be careful when handling syringes, especially those that have been used before.
Pricking yourself with a dirty needle may cause illness or infection. , Pull the plunger back until it comes free of the syringe.
Fill the barrel with cool water from the open plunger end.
Reinsert the plunger and press it down to eject water through the needle and down the drain.
Do this at least 3 times.
When the barrel is full of water, gently shake the syringe and tap the barrel against the palm of your hand.
This will help loosen up hardened blood., Insert your needle into the container with undiluted bleach.
Draw enough bleach into the syringe until the barrel is roughly half full.
Do not overfill the syringe.
Then pull the plunger as far back as possible without removing it. , Lightly shake the syringe.
Tap the barrel lightly against the palm of your hand.
Do this for at least 30 seconds.
The bleach needs at least this much time to disinfect resilient viruses, like hepatitis C and HIV. , Position the syringe over a drain and press in the plunger to eject the bleach down the drain.
Never reuse bleach when cleaning syringes.
Repeat the process of drawing fresh bleach into the syringe, shaking it for 30 seconds, and ejecting the used bleach down the drain two more times. , The water in your container has been contaminated by the dirty needle.
Empty the water down the drain and clean the container with a strong cleaner, like bleach.
Rinse the container several times with cool water.
Refill it with water.
To flush the syringe:
Draw water into the barrel until it is half full.
Remove the needle from the water.
Extend the plunger as far back as possible without detaching it.
Shake the syringe gently.
Press the plunger to eject the water.
Do not reuse water.
Repeat this at least three times., Empty the contents of both containers down the drain.
Use fresh, undiluted bleach to clean the containers and the sink.
Rinse bleach thoroughly with cool water.
Dry the containers with a towel or allow them to air dry, then put them away. , A magnifying glass, especially those used by jewelers or cosmetologists, will help you inspect the condition of the needle.
Arkansas or carbide sharpening stones work best as a sharpening surface and can be bought at medical supply stores.
You’ll also need a clean, small container for water, like a cup.
If a sharpening stone is unavailable, you can use the striking surface of a matchbox as the sharpening surface.
The magnifying glasses used by jewelers and cosmetologists can sometimes be found at flea markets., Only sharpen cleaned needles.
Fill your clean, small container with cool water.
Insert the tip of your needle into the water and draw back the plunger to fill the barrel halfway.
Remove the needle from the water. , Position the needle at one end of the surface so its angled part is flat against the surface.
With extremely light pressure, pull the tip of the needle backwards along the surface until you reach the opposite end.
Take care not to pull the plunger of the syringe while sharpening.
Doing so might draw dangerous fragments created by sharpening into the barrel.
Most needles sharpen in 2 to 3 passes when pulled along the entire length of a sharpening stone or the striking strip of a matchbox.
Pressing too hard on the needle when sharpening could damage the needle.
Syringes with damaged needles should be disposed of in an appropriate container., After pulling the needle the length of the surface, lift the needle and repeat this process at least 2 more times.
Flip the needle so the angled side is facing up and the tip is against the surface.
Pull the needle against the surface once like this to finish sharpening.
Use a magnifying glass, if you have one, to inspect the needle point.
If you notice roughness, pass the needle a few more times along the sharpening surface., Press the plunger to completely eject the water in the barrel.
Wrap an alcohol swab around the base of the needle and pull the needle through the swab.
Throw the swab away.
Repeat this process with a fresh swab to finish cleaning your sharpened needle.
Sharpening a syringe creates small, sometimes invisible needle fragments.
If injected, these can be deadly.
Be thorough when cleaning sharpened needles.
Wet sharpened needles with sterilized water before using them.
This will lubricate the needle, allowing for better penetration. -
Step 2: Prepare your disinfecting area.
-
Step 3: Wash your hands thoroughly.
-
Step 4: Fill one small container with bleach and cold water.
-
Step 5: Draw water into and eject it out of the syringe.
-
Step 6: Pour water into the syringe barrel and eject it
-
Step 7: alternatively.
-
Step 8: Draw bleach into the syringe.
-
Step 9: Shake the syringe.
-
Step 10: Rinse the syringe with bleach at least 3 times.
-
Step 11: Flush the syringe several times with cool water.
-
Step 12: Clean up your disinfecting area.
-
Step 13: Gather your supplies.
-
Step 14: Fill a clean needle with clean water.
-
Step 15: Drag the needle backwards against the sharpening surface.
-
Step 16: Repeat this motion a couple of times.
-
Step 17: Clean the syringe thoroughly.
Detailed Guide
This may seem like a troublesome routine.
However, cleaning syringes right before and after using them will greatly reduce the chances of catching a blood borne disease, like hepatitis or HIV.
This will also prevent blood from hardening in the syringe., Kitchens work best for cleaning syringes, though bathrooms are also suitable in a pinch.
Clean the entire area where you’ll be disinfecting syringes thoroughly with a strong cleaner, like bleach.
Avoid disinfecting syringes in dirty areas.
Doing so could result in your bacteria or viruses being transferred from the work area to disinfected syringes., Wet your hands in cool water.
Apply a household soap to them.
Rub your hands together to lather up the soap.
Pay close attention to the spaces between your fingers and your fingernails.
Bacteria often hides in these places.
Rinse the soap from your hands with cool water.
Wash your hands for at least 20 seconds.
A quick rinse will not effectively remove germs from your hands., If you don’t have suitable containers, use a clean cap or cup.
The containers should be large enough to hold at least a full syringe of fluid.
If your sink is flat bottomed, you may want to place these containers in the sink in case of spillage.
If you don’t have bleach, fill the container with high percentage isopropyl alcohol (90% or higher recommended) or hydrogen peroxide., Place the tip of your needle in the water.
Draw back the plunger to fill the barrel of the syringe.
Lightly shake the syringe.
Position the needle over the drain and press the plunger to eject the water.
Do this several times.
Never reuse fluid that has been inside a syringe.
Fluid used to rinse or disinfect syringes should be disposed down a drain.Be careful when handling syringes, especially those that have been used before.
Pricking yourself with a dirty needle may cause illness or infection. , Pull the plunger back until it comes free of the syringe.
Fill the barrel with cool water from the open plunger end.
Reinsert the plunger and press it down to eject water through the needle and down the drain.
Do this at least 3 times.
When the barrel is full of water, gently shake the syringe and tap the barrel against the palm of your hand.
This will help loosen up hardened blood., Insert your needle into the container with undiluted bleach.
Draw enough bleach into the syringe until the barrel is roughly half full.
Do not overfill the syringe.
Then pull the plunger as far back as possible without removing it. , Lightly shake the syringe.
Tap the barrel lightly against the palm of your hand.
Do this for at least 30 seconds.
The bleach needs at least this much time to disinfect resilient viruses, like hepatitis C and HIV. , Position the syringe over a drain and press in the plunger to eject the bleach down the drain.
Never reuse bleach when cleaning syringes.
Repeat the process of drawing fresh bleach into the syringe, shaking it for 30 seconds, and ejecting the used bleach down the drain two more times. , The water in your container has been contaminated by the dirty needle.
Empty the water down the drain and clean the container with a strong cleaner, like bleach.
Rinse the container several times with cool water.
Refill it with water.
To flush the syringe:
Draw water into the barrel until it is half full.
Remove the needle from the water.
Extend the plunger as far back as possible without detaching it.
Shake the syringe gently.
Press the plunger to eject the water.
Do not reuse water.
Repeat this at least three times., Empty the contents of both containers down the drain.
Use fresh, undiluted bleach to clean the containers and the sink.
Rinse bleach thoroughly with cool water.
Dry the containers with a towel or allow them to air dry, then put them away. , A magnifying glass, especially those used by jewelers or cosmetologists, will help you inspect the condition of the needle.
Arkansas or carbide sharpening stones work best as a sharpening surface and can be bought at medical supply stores.
You’ll also need a clean, small container for water, like a cup.
If a sharpening stone is unavailable, you can use the striking surface of a matchbox as the sharpening surface.
The magnifying glasses used by jewelers and cosmetologists can sometimes be found at flea markets., Only sharpen cleaned needles.
Fill your clean, small container with cool water.
Insert the tip of your needle into the water and draw back the plunger to fill the barrel halfway.
Remove the needle from the water. , Position the needle at one end of the surface so its angled part is flat against the surface.
With extremely light pressure, pull the tip of the needle backwards along the surface until you reach the opposite end.
Take care not to pull the plunger of the syringe while sharpening.
Doing so might draw dangerous fragments created by sharpening into the barrel.
Most needles sharpen in 2 to 3 passes when pulled along the entire length of a sharpening stone or the striking strip of a matchbox.
Pressing too hard on the needle when sharpening could damage the needle.
Syringes with damaged needles should be disposed of in an appropriate container., After pulling the needle the length of the surface, lift the needle and repeat this process at least 2 more times.
Flip the needle so the angled side is facing up and the tip is against the surface.
Pull the needle against the surface once like this to finish sharpening.
Use a magnifying glass, if you have one, to inspect the needle point.
If you notice roughness, pass the needle a few more times along the sharpening surface., Press the plunger to completely eject the water in the barrel.
Wrap an alcohol swab around the base of the needle and pull the needle through the swab.
Throw the swab away.
Repeat this process with a fresh swab to finish cleaning your sharpened needle.
Sharpening a syringe creates small, sometimes invisible needle fragments.
If injected, these can be deadly.
Be thorough when cleaning sharpened needles.
Wet sharpened needles with sterilized water before using them.
This will lubricate the needle, allowing for better penetration.
About the Author
Henry Gibson
Professional writer focused on creating easy-to-follow DIY projects tutorials.
Rate This Guide
How helpful was this guide? Click to rate: