How to Paint the Exterior of a Wooden Structure
Begin your preparation with a power washer., For larger structures, scaffolding may be preferable to ladders. , Scrub all mold with bleach and water and water only, then rinse bleach. , Set all nails with nail set. , Screw all loose siding, trim and...
Step-by-Step Guide
-
Step 1: Begin your preparation with a power washer.
Although it can be effective at cleaning, this must be done very carefully and not at close range, or it can damage siding and drive water into the wood and walls.
The first opinion on this, overruled by the contributors, is that you do not power wash unless you plan to let it dry for at least a month.
You do not want to paint over wet wood.
Take your choice. -
Step 2: For larger structures
,,,, The Makita 5" disk sander is ideal.
Never use paper disk sandpaper, as it doesn't last long and is hard to control.
Use hard board sanding disks usually 80, 100 or 120 grit, depending.
You can sand very lightly with outer one inch of board, and no sanding grooves will show.
Used correctly, this should last half, or most of the day. , Older paint has lead in it and it can give you lead poisoning.
One advantage of the scrubbing is that it reduces the dust that you breath. , use Red Mercury.
However, this is poisonous; wear mask with filters specifically for the chemical. , Redwood window sills may need to be sanded to wood and fiber glassed with Redwood compatible epoxy.
Use some mix of Linseed Oil on dry rot and overly dry wood.
You can also use fiberglass to seal overly damaged dry rot.
Primer with oil base primer.
Never use water base primer outside as it will not hold up on wood. , All tools can be equipped with hangers.
Roll on the paint with a long nap roller for speed, best quality, and then painted out with brush.
A three and one-half inch acrylic angle brush is light, easy to use, and can be used for nearly every application.
A brush holder can be bought which hangs on the bucket.
Spray painting is faster, but will never do the job of hand application, since the paint is usually thinned for the gun.
Beware of contractors who use the cheapest materials, and the fastest means to save labor costs.
Often they charge the highest prices and do the cheapest job. , Fill will stick better to paint, than raw wood.
Fill all nail holes or anything up to one or even two inch diameter with 'Dap 33'
oil base window glaze.
The only thing ever used before someone decided to make money on unnecessary substitutes.
Allow the surface to glaze over for more than one day before painting.
You can also use fiber glass filler for large holes.
Use elastomeric, paintable caulk, the most long lasting that you can get, for most vertical joints, cracks, some knot holes.
Seal up vertical framing like windows and trim.
Do not caulk overlapping horizontal ship lap, and use a cutting tool to open already sealed, although this is tough and may not be necessary.
The theory is this allows breath-ability. , If you do not use exterior primer, the "oxidation" on the old paint will burn the new paint and between 1 and 2 years it will peal off.
If you prime with exterior primer, the paint will last over a decade.
I painted 2 homes and a duplex in 2000 with an expensive exterior primer and in 2010 I still do not have any peeling. , Lighter paint reflects the sun; darker paint absorbs it, and tends to break down faster.
Best to use 2 coats of only '100 percent acrylic'
over oil base primer.
Exterior latex will not last.
Two coats will last longer than one.
A good paint job should last ten to fifteen years.
Usually like everything, the best paint costs the most money.
Use big-brand, and do not buy paint from chain hardware and discount stores, since they tend to be primarily interested in profit. -
Step 3: scaffolding may be preferable to ladders.
-
Step 4: Scrub all mold with bleach and water and water only
-
Step 5: then rinse bleach.
-
Step 6: Set all nails with nail set.
-
Step 7: Screw all loose siding
-
Step 8: trim and accessories.
-
Step 9: Sand all loose paint.
-
Step 10: When you sand loose paint
-
Step 11: use a painters mask to avoid breathing fine paint dust.
-
Step 12: To seal rusted nails drain pipes etc.
-
Step 13: Break painted-in windows and repair window glaze by removing loose and patching.
-
Step 14: Put paint into a 5 gallon (18.9Â L) bucket with a roller screen
-
Step 15: in combination with a hook
-
Step 16: to hang it from ladders and scaffold
-
Step 17: and as a catch if it should slip.
-
Step 18: Do filling.
-
Step 19: You must use paint over the entire exterior surface with exterior primer before you paint.
-
Step 20: Choose paint.
Detailed Guide
Although it can be effective at cleaning, this must be done very carefully and not at close range, or it can damage siding and drive water into the wood and walls.
The first opinion on this, overruled by the contributors, is that you do not power wash unless you plan to let it dry for at least a month.
You do not want to paint over wet wood.
Take your choice.
,,,, The Makita 5" disk sander is ideal.
Never use paper disk sandpaper, as it doesn't last long and is hard to control.
Use hard board sanding disks usually 80, 100 or 120 grit, depending.
You can sand very lightly with outer one inch of board, and no sanding grooves will show.
Used correctly, this should last half, or most of the day. , Older paint has lead in it and it can give you lead poisoning.
One advantage of the scrubbing is that it reduces the dust that you breath. , use Red Mercury.
However, this is poisonous; wear mask with filters specifically for the chemical. , Redwood window sills may need to be sanded to wood and fiber glassed with Redwood compatible epoxy.
Use some mix of Linseed Oil on dry rot and overly dry wood.
You can also use fiberglass to seal overly damaged dry rot.
Primer with oil base primer.
Never use water base primer outside as it will not hold up on wood. , All tools can be equipped with hangers.
Roll on the paint with a long nap roller for speed, best quality, and then painted out with brush.
A three and one-half inch acrylic angle brush is light, easy to use, and can be used for nearly every application.
A brush holder can be bought which hangs on the bucket.
Spray painting is faster, but will never do the job of hand application, since the paint is usually thinned for the gun.
Beware of contractors who use the cheapest materials, and the fastest means to save labor costs.
Often they charge the highest prices and do the cheapest job. , Fill will stick better to paint, than raw wood.
Fill all nail holes or anything up to one or even two inch diameter with 'Dap 33'
oil base window glaze.
The only thing ever used before someone decided to make money on unnecessary substitutes.
Allow the surface to glaze over for more than one day before painting.
You can also use fiber glass filler for large holes.
Use elastomeric, paintable caulk, the most long lasting that you can get, for most vertical joints, cracks, some knot holes.
Seal up vertical framing like windows and trim.
Do not caulk overlapping horizontal ship lap, and use a cutting tool to open already sealed, although this is tough and may not be necessary.
The theory is this allows breath-ability. , If you do not use exterior primer, the "oxidation" on the old paint will burn the new paint and between 1 and 2 years it will peal off.
If you prime with exterior primer, the paint will last over a decade.
I painted 2 homes and a duplex in 2000 with an expensive exterior primer and in 2010 I still do not have any peeling. , Lighter paint reflects the sun; darker paint absorbs it, and tends to break down faster.
Best to use 2 coats of only '100 percent acrylic'
over oil base primer.
Exterior latex will not last.
Two coats will last longer than one.
A good paint job should last ten to fifteen years.
Usually like everything, the best paint costs the most money.
Use big-brand, and do not buy paint from chain hardware and discount stores, since they tend to be primarily interested in profit.
About the Author
Douglas Henderson
Creates helpful guides on lifestyle to inspire and educate readers.
Rate This Guide
How helpful was this guide? Click to rate: