How to Apply Duracoat
Cover the surface where you will be working with newspaper., Dis-assemble the entire firearm and clean all pieces thoroughly, making sure there is no trace of oil on any piece., Use denatured alcohol for a final wipe down of the parts., Use blue...
Step-by-Step Guide
-
Step 1: Cover the surface where you will be working with newspaper.
One of the best cleaners you can use for this job is MEK or methyl ethyl ketone, an industrial solvent.
Pour MEK into a disposable aluminum foil pan and soak the parts.
If necessary, use air pressure, brushes or rags to reach every surface of the firearm. , Even a single drop of oil will cause the Duracoat to peel. ,, This will also facilitate spraying Duracoat and allowing drying time between coats.
A pegboard will work as a holder for hanging the parts.
Cover the pegboard with heavy plastic to protect the surface from over spray. , In case of a painting mistake, dip the part into the pan to remove the paint.
You can also use it to clear the air-sprayer tip if necessary or to clean your hands of excess paint. ,, Test spray on a scrap piece of metal to check color. , Shake thoroughly for at least 3 minutes, and pour into the paint receptacle on the air-sprayer. , You can go back for another pass or 2 before allowing it to dry.
The ideal final thickness of Duracoat should be 1 mil, applied in 1 to 3 passes.
When spraying Duracoat on parts that receive more wear, such as parts that rub against holsters and slings, aim for a coating
1.5 mil for added endurance. , They will be dry enough for light use in 24 hours, but ideally they should be allowed to dry for 2 weeks. , Do not dispose of Duracoat and other chemicals in sewer lines.
If you will not use up the Duracoat within 18 months, take to a licensed disposal facility. -
Step 2: Dis-assemble the entire firearm and clean all pieces thoroughly
-
Step 3: making sure there is no trace of oil on any piece.
-
Step 4: Use denatured alcohol for a final wipe down of the parts.
-
Step 5: Use blue painter's tape to mask off any parts that will not be painted.
-
Step 6: Snip pieces of the wire to make hooks to hang the parts to dry.
-
Step 7: Pour lacquer thinner into a foil pan.
-
Step 8: Set up the air sprayer and set the compressor to 30 psi.
-
Step 9: Mix the Duracoat paints to get the color you desire.
-
Step 10: Combine 1 part Duracoat Hardener to 12 parts Duracoat paint.
-
Step 11: Hold spray tip 4 to 8 inches (10.2 to 20.3 cm) from the parts and spray Duracoat with sweeping passes from left to right.
-
Step 12: Set parts aside to dry and cure.
-
Step 13: Clean up work area.
Detailed Guide
One of the best cleaners you can use for this job is MEK or methyl ethyl ketone, an industrial solvent.
Pour MEK into a disposable aluminum foil pan and soak the parts.
If necessary, use air pressure, brushes or rags to reach every surface of the firearm. , Even a single drop of oil will cause the Duracoat to peel. ,, This will also facilitate spraying Duracoat and allowing drying time between coats.
A pegboard will work as a holder for hanging the parts.
Cover the pegboard with heavy plastic to protect the surface from over spray. , In case of a painting mistake, dip the part into the pan to remove the paint.
You can also use it to clear the air-sprayer tip if necessary or to clean your hands of excess paint. ,, Test spray on a scrap piece of metal to check color. , Shake thoroughly for at least 3 minutes, and pour into the paint receptacle on the air-sprayer. , You can go back for another pass or 2 before allowing it to dry.
The ideal final thickness of Duracoat should be 1 mil, applied in 1 to 3 passes.
When spraying Duracoat on parts that receive more wear, such as parts that rub against holsters and slings, aim for a coating
1.5 mil for added endurance. , They will be dry enough for light use in 24 hours, but ideally they should be allowed to dry for 2 weeks. , Do not dispose of Duracoat and other chemicals in sewer lines.
If you will not use up the Duracoat within 18 months, take to a licensed disposal facility.
About the Author
Michelle Johnson
Experienced content creator specializing in organization guides and tutorials.
Rate This Guide
How helpful was this guide? Click to rate: