How to Cut Glass
Set up your work area., Clean the glass surface in the area where you plan to make cuts., Obtain a glass cutter and some light oil., Measure and mark where you want to score., Dip the cutter in the oil and grasp it like a pencil., Lay out a straight...
Step-by-Step Guide
-
Step 1: Set up your work area.
You'll need a large flat surface, preferably one that is slightly soft and won't scratch your glass.
Work in an area that is easy to clean.
Avoid working over carpet because of the risk of getting glass shards on the floor if the glass breaks.
For their own safety keep pets and children away from your workspace and materials. -
Step 2: Clean the glass surface in the area where you plan to make cuts.
Any grime or silica on the glass can ruin your score.
Wipe these away by running a cloth or your finger along the surface of the glass where you plan to score. , Glass cutters are about the size of a pencil and use a diamond or a hardened wheel to mark a score into glass so that it can be broken cleanly along a line.
You can buy cutting oil at a stained glass store or use a small amount of kerosene. , The score must run from one edge of the glass to the other edge.
You can write on the glass with a marker (preferably with a straight edge, if you are cutting a straight line.
You can also mark on paper and place the glass on top of the paper.
Cut should not be very long.
Scores longer than two feet have a high failure rate when breaking.
Make sure your marks leave about six inches of glass on each side to grip and break.
If you cut smaller pieces, you may need to use special tools, like pliers or a light hammer, to break off glass you can't get a hold of. , An oiled cutter creates a smoother score line.
Make sure to look at the wheel and make sure it is lined up the way you want the glass to cut. , Use a yardstick or a normal desk ruler.
You need something that has a thick enough profile that it won't conflict with the wheel on the cutter. , Listen for a smooth sound like ripping silk.
A gritty sound means that you are pushing too hard or that you did not oil your cutter.
The less sound you make, the better your score will be.
If you push too hard (a very common mistake), your cut gets "hot," meaning that it snaps and pops.
You are aiming to get a uniform score.
If you are pressing too hard in one spot and perfectly in another, the glass will not break the way that you want it to.
Microscopic imperfections in your score will cause your cut to go askew. , Do not run back and forth over the line if you miss a spot. , You want a score that is not popping and is barely visible, if you were to wipe the oil away.
It should look like a small scratch, nothing more.
Make sure it runs completely from one edge to the other. , Hold the glass as if you were trying to break a potato chip in half with two hands. , Your elbows do not move.
Simply twist your wrists (your right wrist will turn clockwise and your left will turn counterclockwise).
Imagine that the score you made is half the depth of the glass and now you need to "open it up" by using the score as a weak spot.
You're done as soon as you have two pieces of glass instead of the one you started with.
When the glass breaks, it may simply start as a "run." If it only runs an inch or so, apply a little more twisting pressure and it will continue to run. , This edge will be where the vertical edge meets the horizontal surfaces.
Not only does sanding reduce the chances of your being cut, but sanded glass is less likely to chip along the edges and has some added strength. , If you are cutting a freehand shape, make sure you are breaking along lines that run from edge to edge.
Mark your lines with a marker or set your glass over your pattern. , You should be able to score along gentle curves normally with a steady hand.
For tighter curves, make a series of marks that run along part of the curve and skew off at a tangent outside the piece you want. , You will start a run this way.
Follow the run with light pressure and you can watch the glass separate where you scored it.
If your score is too close to the edge of a piece of glass, it may run to the edge instead of along your score because that is the easiest path for the run to take. , The smaller the relief cuts, the more accurate your cut will be.
Grip smaller pieces with pliers to snap them off. , This machine uses a spinning wheel with fine diamond chips as a grinder.
Turn on the router and press your curve firmly against the grinder to smooth out your curve, then sand as normal. -
Step 3: Obtain a glass cutter and some light oil.
-
Step 4: Measure and mark where you want to score.
-
Step 5: Dip the cutter in the oil and grasp it like a pencil.
-
Step 6: Lay out a straight edge.
-
Step 7: Apply pressure to the glass and you pull the cutter along the surface
-
Step 8: rolling on the small carbide wheel.
-
Step 9: Run the cutter smoothly from one edge to the other.
-
Step 10: Check your score.
-
Step 11: Grasp each side of the cut carefully in your hands.
-
Step 12: Apply minor pressure from the wrist to break the glass along your score.
-
Step 13: Use fine sandpaper or a sharpening stone to remove the sharp edge.
-
Step 14: Follow a pattern that connects to the edge.
-
Step 15: Use several straight lines to cut a sharp curve.
-
Step 16: Flip the glass over and gently press on the center of your score from the backside.
-
Step 17: Make some relief cuts to remove small pieces at a time instead of all at once.
-
Step 18: Smooth your curved edges using a glass router.
Detailed Guide
You'll need a large flat surface, preferably one that is slightly soft and won't scratch your glass.
Work in an area that is easy to clean.
Avoid working over carpet because of the risk of getting glass shards on the floor if the glass breaks.
For their own safety keep pets and children away from your workspace and materials.
Any grime or silica on the glass can ruin your score.
Wipe these away by running a cloth or your finger along the surface of the glass where you plan to score. , Glass cutters are about the size of a pencil and use a diamond or a hardened wheel to mark a score into glass so that it can be broken cleanly along a line.
You can buy cutting oil at a stained glass store or use a small amount of kerosene. , The score must run from one edge of the glass to the other edge.
You can write on the glass with a marker (preferably with a straight edge, if you are cutting a straight line.
You can also mark on paper and place the glass on top of the paper.
Cut should not be very long.
Scores longer than two feet have a high failure rate when breaking.
Make sure your marks leave about six inches of glass on each side to grip and break.
If you cut smaller pieces, you may need to use special tools, like pliers or a light hammer, to break off glass you can't get a hold of. , An oiled cutter creates a smoother score line.
Make sure to look at the wheel and make sure it is lined up the way you want the glass to cut. , Use a yardstick or a normal desk ruler.
You need something that has a thick enough profile that it won't conflict with the wheel on the cutter. , Listen for a smooth sound like ripping silk.
A gritty sound means that you are pushing too hard or that you did not oil your cutter.
The less sound you make, the better your score will be.
If you push too hard (a very common mistake), your cut gets "hot," meaning that it snaps and pops.
You are aiming to get a uniform score.
If you are pressing too hard in one spot and perfectly in another, the glass will not break the way that you want it to.
Microscopic imperfections in your score will cause your cut to go askew. , Do not run back and forth over the line if you miss a spot. , You want a score that is not popping and is barely visible, if you were to wipe the oil away.
It should look like a small scratch, nothing more.
Make sure it runs completely from one edge to the other. , Hold the glass as if you were trying to break a potato chip in half with two hands. , Your elbows do not move.
Simply twist your wrists (your right wrist will turn clockwise and your left will turn counterclockwise).
Imagine that the score you made is half the depth of the glass and now you need to "open it up" by using the score as a weak spot.
You're done as soon as you have two pieces of glass instead of the one you started with.
When the glass breaks, it may simply start as a "run." If it only runs an inch or so, apply a little more twisting pressure and it will continue to run. , This edge will be where the vertical edge meets the horizontal surfaces.
Not only does sanding reduce the chances of your being cut, but sanded glass is less likely to chip along the edges and has some added strength. , If you are cutting a freehand shape, make sure you are breaking along lines that run from edge to edge.
Mark your lines with a marker or set your glass over your pattern. , You should be able to score along gentle curves normally with a steady hand.
For tighter curves, make a series of marks that run along part of the curve and skew off at a tangent outside the piece you want. , You will start a run this way.
Follow the run with light pressure and you can watch the glass separate where you scored it.
If your score is too close to the edge of a piece of glass, it may run to the edge instead of along your score because that is the easiest path for the run to take. , The smaller the relief cuts, the more accurate your cut will be.
Grip smaller pieces with pliers to snap them off. , This machine uses a spinning wheel with fine diamond chips as a grinder.
Turn on the router and press your curve firmly against the grinder to smooth out your curve, then sand as normal.
About the Author
Gregory Stokes
Specializes in breaking down complex practical skills topics into simple steps.
Rate This Guide
How helpful was this guide? Click to rate: