How to Felt a Pool Table
Begin disassembling the pool table., Remove the old felt., Level the table (optional)., Clean the slate., Seal the seams with beeswax if necessary., Measure your pool table before purchasing felt., Use this method if there is a wooden or particle...
Step-by-Step Guide
-
Step 1: Begin disassembling the pool table.
Remove the pocket liners from each pocket first, if any are present.
Next, find the bolts on the underside of the table keeping the railings in place, and remove them.
Move the railing carefully to a safe storage space where it won't get scuffed or damaged, or interfere with your movement around the pool table.
The railing may be composed of one, two, or four pieces.If the railing does not divide into four pieces, you will likely need an assistant to transport it safely.
Some pool table pockets are bolted or screwed on separately from the railings. -
Step 2: Remove the old felt.
Felt can be attached in more than one way.
Use a staple remover if the felt is stapled to the table.
If it is glued, you can simply rip the felt off, but be careful not to damage any felt in the pockets unless you also plan on replacing those portions as well., You may wish to use a level to test whether your billiards table is flat.
If it is not, use a small pry bar to lift the lowest leg and add a wooden or metal shim. , Use a dry, clean cloth to remove dust.
Do not use any water or cleaning solutions.
If old glue or other residue has built up, scrape this off with a putty knife or other flat blade, especially where it may block pockets., Most pool tables are constructed from three pieces of slate.
On an old pool table, the seams between these may have lost some of the wax that fills them in to create a flat surface.
If the wax needs replenishing, heat the slate around the seams with a propane hand torch, then drip wax into these seams.
Spread the wax evenly across the seam line, let it cool for no more than thirty seconds, then scrape excess wax down to the level of the table surface using a paint scraper.It's better to remove too much wax than too little, since excess wax can be difficult to remove once dry.
If your pool table is kept in a warm location, you may wish to use putty specifically formulated for pool tables.
There is a great deal of disagreement over which of these synthetic products produces the best quality table, so you may wish to consult a local expert familiar with your climate. , Measuring will take the guesswork out of sizing your felt, resulting in a faster process and a cleaner result.
When you purchase the felt, or more technically the pool tablecloth, for your table, make sure it is at least 12 inches (30.5 cm) longer than the table on all four sides.
This ensures that you will have plenty of cloth for the railings as well as the table surface.
Note that pool felt is actually a special type of cloth, and while it is commonly referred to as "felt," it is usually sold as "pool tablecloth," "pool cloth," or "billiards cloth." You cannot use ordinary felt to cover your pool table.
Woolen pool cloth is the pool felt most players are familiar with.
Worsted cloth allows for greater speed, but is rarely used outside of professional tournaments due to its lessened durability and price.
Other varieties such as snooker cloth, carom, or polyester cloth are only suitable for certain uses., Many tables have a wooden or particle board layer beneath the slate, allowing staples to be attached.
You can check whether this is true of your table by examining the perimeter or vertical edge of your table.
If there is only slate, use the instructions for gluing the felt instead.
Note:
You will need a "hammer tacker" or manual stapler, or a staple gun. , Typically, the felt comes in one large piece, and includes instructions for removing pieces to fit each railing.
Follow these instructions carefully, or the cut pieces may not fit your table.
With some felt, you can make a one inch (2.5 cm) cut, then rip the felt by hand in a straight line.Other felt may require cutting with a razor blade or box cutter. , Look for a sticker or other label that tells you which side is face up.
If it is unlabeled, and you cannot easily tell which side is the playing surface, consult a professional.
Different types of felt have a different feel, so it's best not to guess if you are not familiar with the feel of that type.
Hang more of the extra felt over the foot end, and not much on the head end where you will begin installation.
Check now for rips, scratches, or other defects that could require you to get a refund or replacement. , Use your hammer tacker or staple gun to attach the felt to the wooden or particle board lining of the table at one corner of the head end.
Have an assistant help you stretch the felt across the head end until there are no wrinkles present, keeping the overhang parallel with the table edge.
Staple about every 3 inches (7.5 cm) along this stretched edge, ending at the second corner.
Professionals play on a very tightly stretched surface, which allows for greater speed.
This is not necessarily desirable for most players, however, who may enjoy playing on a slower table.Always stretch at least tightly enough to remove all wrinkles, however. , Move to one of the long sides of the table, and have an assistant help you pull the felt taut along its length.
Staple at roughly 3 inch (7.5 cm) increments, but make sure to staple on either side of the side pocket.
Pulling the felt over each pocket when stapling on either side will give you extra material to work with when lining the pockets. , Pull the felt tight from the last unstapled corner.
Pay special attention to this, as an inconsistent pull can cause wrinkles in your table.
If the previous staples make it impossible to create a flat surface with this pull, with the overhang parallel with the table end, you may need to remove a couple staples with a staple puller and try again.
Once this is pulled to a smooth surface with the desired tightness, staple the short foot end and remaining right sides along their lengths.Remember to staple on each side of the side pocket. , Make three slits in the felt directly over each pocket, then fold the loose felt down into the pocket and staple it inside the pocket.
Once this is done, use a pair of scissors or a razor blade to snip off the excess felt. , If your table has no wooden or particle board backing underneath the slate surface, you'll need to find a specialized adhesive to glue the felt to the slate instead.
If you do see that backing, follow the instructions for stapling the felt instead. 3M Super 77 Multipurpose Adhesive is a popular option. , Protect the edges of the table from spilled glue with a layer of newspaper, overhanging the edge.Remove newspaper from each edge just before you lower the glued felt. , Felt usually comes in one large pieces, along with instructions for cutting off strips for each railing.
Follow these instructions to ensure you end up with pieces of the correct size. , If the "face up" surface is not labeled, try to identify it by feel or consult a professional.
Your felt playing surface may be smooth, or it may have a "nap" in one direction, depending on the type; you may need to have an expert identify the face-up side if you are not familiar with the material.
Arrange the felt over the table, leaving only a couple inches (a few centimeters) of overhand on the short head end.
Make sure each overhang is as parallel to the table edge as possible. , Fold the head end of the felt over onto the table, exposing the underside that will hang over the vertical side of the slate.
Spray that portion of the underside heavily with the adhesive, and spray the slate where it will be attached as well.Let this sit until it becomes tacky, according to the adhesive manufacturer's instructions. , Starting at one end, align the glued felt carefully with the slate, press down, then move along the glued end, pulling tightly as you attach it to the table.
You may need an assistant to ensure the material is taut, especially at the beginning of the process.
The felt should be tight enough to prevent all wrinkles, but an ultra-tight surface is not necessary unless you want to practice for professional tournaments.Most importantly, you should pull the felt with the same pressure throughout this installation. , The gluing process is identical for each of the remaining three sides.
Wait at least a couple minutes between each side, or however long the adhesive manufacturer recommends to create a strong initial bond.
Carefully pull each side taut before you apply glue, making sure there are no wrinkles on the cloth and you are pulling with the same force on every side. , Trim the excess felt overhang on each side.
One one side, cut a one inch (2.5 cm) wide strip of material for use as pocket liner.
Cut off the material stretched over the pockets, then cut this strip into smaller pieces, gluing them over the vertical, circular surface of the slate to protect it from the pool balls. , Use a staple puller or flathead screwdriver to remove the staples from the ends of the rails.
Cut the old felt along the top of the rail if it does not come off immediately., Each rail has a thin wooden "featherstrip" running alongside it, which is typically not attached by any adhesive or nails.
If it won't come up easily, Use a thin flathead screwdriver to pry it up without breaking it. , Unlike the table top, this felt should be "face side" down.
Keep an overhang of at least 4 inches (10 cm) on each end, and 1 , Lay the featherstrip back in position, but do not press it down.
Have an assistant stretch the felt tightly between the center and one end of the railing.
Place a tapping block over the featherstrip, then use a hammer to gently tap the block, pushing the featherstrip down into the stretched portion of the felt, but stop about 2 inches (5 cm) from the end, where the corner pocket will be located.Stretch the other half of the felt, and repeat this process for the remaining length of the featherstrip, again stopping 2 inches (5 cm) away from the other end.
Do not strike the featherstrip directly, or you may dent the table. , Pull the felt at the ends of the table toward the rubber cushion, then tap in the remaining portion of the featherstrip until it is firmly in place.
Trim and fold the felt as necessary to remove excess material and cover the ends of the cushion. , Once all your rails are complete, bolt them to the table again.
If you're having a hard time finding where the bolts should go, you can push a screwdriver through the bolt holes as guidance.
Never try to cut holes in the playing surface from the top of the table, as you may cut in the wrong place. -
Step 3: Level the table (optional).
-
Step 4: Clean the slate.
-
Step 5: Seal the seams with beeswax if necessary.
-
Step 6: Measure your pool table before purchasing felt.
-
Step 7: Use this method if there is a wooden or particle board backing.
-
Step 8: Cut the felt into pieces for the table and railing.
-
Step 9: Roll the felt out face up over table.
-
Step 10: Stretch the felt across the head end and staple it on the vertical edge in several places.
-
Step 11: Repeat the process on the left side.
-
Step 12: Staple on the foot end
-
Step 13: then the right side.
-
Step 14: Trim the material at the pockets and staple it inside.
-
Step 15: Use specialized spray adhesive if the table cannot be stapled.
-
Step 16: Cover the sides of the table with newspaper.
-
Step 17: Cut the felt according to the manufacturer's instructions.
-
Step 18: Identify the playing surface and place the felt over the table.
-
Step 19: Fold the head end of the felt up and apply glue.
-
Step 20: Carefully attach the felt to the table.
-
Step 21: Repeat the process with the far end and the long sides.
-
Step 22: Trim the felt
-
Step 23: and use the excess to line the pockets.
-
Step 24: Remove old felt from rails.
-
Step 25: Gently remove the wooden feather strip.
-
Step 26: Place a new strip of felt over the rail.
-
Step 27: Use a tapping block and hammer to wedge in the center of the featherstrip.
-
Step 28: Pull felt toward the cushion and tap in the ends of featherstrip.
-
Step 29: Reassemble the outer rails.
Detailed Guide
Remove the pocket liners from each pocket first, if any are present.
Next, find the bolts on the underside of the table keeping the railings in place, and remove them.
Move the railing carefully to a safe storage space where it won't get scuffed or damaged, or interfere with your movement around the pool table.
The railing may be composed of one, two, or four pieces.If the railing does not divide into four pieces, you will likely need an assistant to transport it safely.
Some pool table pockets are bolted or screwed on separately from the railings.
Felt can be attached in more than one way.
Use a staple remover if the felt is stapled to the table.
If it is glued, you can simply rip the felt off, but be careful not to damage any felt in the pockets unless you also plan on replacing those portions as well., You may wish to use a level to test whether your billiards table is flat.
If it is not, use a small pry bar to lift the lowest leg and add a wooden or metal shim. , Use a dry, clean cloth to remove dust.
Do not use any water or cleaning solutions.
If old glue or other residue has built up, scrape this off with a putty knife or other flat blade, especially where it may block pockets., Most pool tables are constructed from three pieces of slate.
On an old pool table, the seams between these may have lost some of the wax that fills them in to create a flat surface.
If the wax needs replenishing, heat the slate around the seams with a propane hand torch, then drip wax into these seams.
Spread the wax evenly across the seam line, let it cool for no more than thirty seconds, then scrape excess wax down to the level of the table surface using a paint scraper.It's better to remove too much wax than too little, since excess wax can be difficult to remove once dry.
If your pool table is kept in a warm location, you may wish to use putty specifically formulated for pool tables.
There is a great deal of disagreement over which of these synthetic products produces the best quality table, so you may wish to consult a local expert familiar with your climate. , Measuring will take the guesswork out of sizing your felt, resulting in a faster process and a cleaner result.
When you purchase the felt, or more technically the pool tablecloth, for your table, make sure it is at least 12 inches (30.5 cm) longer than the table on all four sides.
This ensures that you will have plenty of cloth for the railings as well as the table surface.
Note that pool felt is actually a special type of cloth, and while it is commonly referred to as "felt," it is usually sold as "pool tablecloth," "pool cloth," or "billiards cloth." You cannot use ordinary felt to cover your pool table.
Woolen pool cloth is the pool felt most players are familiar with.
Worsted cloth allows for greater speed, but is rarely used outside of professional tournaments due to its lessened durability and price.
Other varieties such as snooker cloth, carom, or polyester cloth are only suitable for certain uses., Many tables have a wooden or particle board layer beneath the slate, allowing staples to be attached.
You can check whether this is true of your table by examining the perimeter or vertical edge of your table.
If there is only slate, use the instructions for gluing the felt instead.
Note:
You will need a "hammer tacker" or manual stapler, or a staple gun. , Typically, the felt comes in one large piece, and includes instructions for removing pieces to fit each railing.
Follow these instructions carefully, or the cut pieces may not fit your table.
With some felt, you can make a one inch (2.5 cm) cut, then rip the felt by hand in a straight line.Other felt may require cutting with a razor blade or box cutter. , Look for a sticker or other label that tells you which side is face up.
If it is unlabeled, and you cannot easily tell which side is the playing surface, consult a professional.
Different types of felt have a different feel, so it's best not to guess if you are not familiar with the feel of that type.
Hang more of the extra felt over the foot end, and not much on the head end where you will begin installation.
Check now for rips, scratches, or other defects that could require you to get a refund or replacement. , Use your hammer tacker or staple gun to attach the felt to the wooden or particle board lining of the table at one corner of the head end.
Have an assistant help you stretch the felt across the head end until there are no wrinkles present, keeping the overhang parallel with the table edge.
Staple about every 3 inches (7.5 cm) along this stretched edge, ending at the second corner.
Professionals play on a very tightly stretched surface, which allows for greater speed.
This is not necessarily desirable for most players, however, who may enjoy playing on a slower table.Always stretch at least tightly enough to remove all wrinkles, however. , Move to one of the long sides of the table, and have an assistant help you pull the felt taut along its length.
Staple at roughly 3 inch (7.5 cm) increments, but make sure to staple on either side of the side pocket.
Pulling the felt over each pocket when stapling on either side will give you extra material to work with when lining the pockets. , Pull the felt tight from the last unstapled corner.
Pay special attention to this, as an inconsistent pull can cause wrinkles in your table.
If the previous staples make it impossible to create a flat surface with this pull, with the overhang parallel with the table end, you may need to remove a couple staples with a staple puller and try again.
Once this is pulled to a smooth surface with the desired tightness, staple the short foot end and remaining right sides along their lengths.Remember to staple on each side of the side pocket. , Make three slits in the felt directly over each pocket, then fold the loose felt down into the pocket and staple it inside the pocket.
Once this is done, use a pair of scissors or a razor blade to snip off the excess felt. , If your table has no wooden or particle board backing underneath the slate surface, you'll need to find a specialized adhesive to glue the felt to the slate instead.
If you do see that backing, follow the instructions for stapling the felt instead. 3M Super 77 Multipurpose Adhesive is a popular option. , Protect the edges of the table from spilled glue with a layer of newspaper, overhanging the edge.Remove newspaper from each edge just before you lower the glued felt. , Felt usually comes in one large pieces, along with instructions for cutting off strips for each railing.
Follow these instructions to ensure you end up with pieces of the correct size. , If the "face up" surface is not labeled, try to identify it by feel or consult a professional.
Your felt playing surface may be smooth, or it may have a "nap" in one direction, depending on the type; you may need to have an expert identify the face-up side if you are not familiar with the material.
Arrange the felt over the table, leaving only a couple inches (a few centimeters) of overhand on the short head end.
Make sure each overhang is as parallel to the table edge as possible. , Fold the head end of the felt over onto the table, exposing the underside that will hang over the vertical side of the slate.
Spray that portion of the underside heavily with the adhesive, and spray the slate where it will be attached as well.Let this sit until it becomes tacky, according to the adhesive manufacturer's instructions. , Starting at one end, align the glued felt carefully with the slate, press down, then move along the glued end, pulling tightly as you attach it to the table.
You may need an assistant to ensure the material is taut, especially at the beginning of the process.
The felt should be tight enough to prevent all wrinkles, but an ultra-tight surface is not necessary unless you want to practice for professional tournaments.Most importantly, you should pull the felt with the same pressure throughout this installation. , The gluing process is identical for each of the remaining three sides.
Wait at least a couple minutes between each side, or however long the adhesive manufacturer recommends to create a strong initial bond.
Carefully pull each side taut before you apply glue, making sure there are no wrinkles on the cloth and you are pulling with the same force on every side. , Trim the excess felt overhang on each side.
One one side, cut a one inch (2.5 cm) wide strip of material for use as pocket liner.
Cut off the material stretched over the pockets, then cut this strip into smaller pieces, gluing them over the vertical, circular surface of the slate to protect it from the pool balls. , Use a staple puller or flathead screwdriver to remove the staples from the ends of the rails.
Cut the old felt along the top of the rail if it does not come off immediately., Each rail has a thin wooden "featherstrip" running alongside it, which is typically not attached by any adhesive or nails.
If it won't come up easily, Use a thin flathead screwdriver to pry it up without breaking it. , Unlike the table top, this felt should be "face side" down.
Keep an overhang of at least 4 inches (10 cm) on each end, and 1 , Lay the featherstrip back in position, but do not press it down.
Have an assistant stretch the felt tightly between the center and one end of the railing.
Place a tapping block over the featherstrip, then use a hammer to gently tap the block, pushing the featherstrip down into the stretched portion of the felt, but stop about 2 inches (5 cm) from the end, where the corner pocket will be located.Stretch the other half of the felt, and repeat this process for the remaining length of the featherstrip, again stopping 2 inches (5 cm) away from the other end.
Do not strike the featherstrip directly, or you may dent the table. , Pull the felt at the ends of the table toward the rubber cushion, then tap in the remaining portion of the featherstrip until it is firmly in place.
Trim and fold the felt as necessary to remove excess material and cover the ends of the cushion. , Once all your rails are complete, bolt them to the table again.
If you're having a hard time finding where the bolts should go, you can push a screwdriver through the bolt holes as guidance.
Never try to cut holes in the playing surface from the top of the table, as you may cut in the wrong place.
About the Author
Martha Murphy
Creates helpful guides on cooking to inspire and educate readers.
Rate This Guide
How helpful was this guide? Click to rate: