How to Make a Hygrometer
Gather the necessary materials., Clean the hair with diluted rubbing alcohol., Cut a small triangle pointer., Tape the dime onto the tip of the pointer., Attach the hair to the pointer., Fasten the pointer to the wood block with a pin or nail...
Step-by-Step Guide
-
Step 1: Gather the necessary materials.
To make a hair hygrometer you will need 2-3 pieces of hair at least 12 inches long, a 9 inch by 4 inch wooden block or piece of cardboard, two pins or nails, rubbing alcohol, a dime, tape, a marker, a sheet of plastic transparency, a ruler, scissors, and a hair dryer.Most of these materials should be easily found around the home.
If you’re using nails, you will also need a hammer.
Parental supervision is advised during use of the hammer.
You can also substitute the transparency sheet for stiff cardstock or cardboard. -
Step 2: Clean the hair with diluted rubbing alcohol.
Mix 2 drops of alcohol and 8 drops of water.
Wipe the hairs with the mixture to remove oils or hair care products.
The cleaner the hair is, the more water it will be able to absorb.Keep the hair on a white piece of paper so you don’t lose it while you build the rest of the hygrometer.
Clean multiple strands of hair in case some break during the assembly process. , This pointer will be the arrow that allows you to measure relative humidity.
The pointer can be made out of stiff cardboard or the plastic transparency sheet.
Trace a triangle onto the sheet that has a base of 3 inches and sides that are about
2.5 inches tall.
Cut out the triangle using scissors.
Mark a spot about
1.5 centimeters from the base of the triangle in the center.
This will be the attachment point for the pointer. , Using a piece of tape, attach the dime close to the tip of the pointer.
It’s okay if the dime hangs off the edges a little bit.The dime serves as a weight, to keep the hair taut and straight.
If tape does not work, you can use a dab of hot glue.
Keep in mind, this is a slightly more permanent solution. , Glue the hair to the hygrometer pointer between the dime and the marking for the attachment point.
The hair should be perpendicular (make a 90 degree angle) to the pointer. , Using the mark you made earlier, poke a hole through the pointer with a pin or nail.
Hammer the pin/nail into the 9-inch-by-4-inch (22.86-cm-by-10.16-cm) wood block base about 6 3/4 inches (17.15 cm) from the top, with the pointer parallel to the ground (hanging horizontally).
Make sure the hole is large enough for the pointer to swivel around the nail. , Measure 1 inch from the top of the block and mark a point that is straight up from where the hair is positioned.
Hammer the nail into this spot on the block.
This second nail will be the anchor point for the hair. , Pull the piece of hair taut and wrap it around the nail at the top of the block.
Add a dab of glue to secure the hair in place.
You may need to hold the hair while the glue dries to make sure it is taut.
Make sure the hair is pulled tight and the tip of the pointer is horizontally straight/parallel to the ground.
Trim any extra hair. , Using a hair dryer and a wet rag, you can simulate the conditions of zero and one hundred percent humidity.
Dry the hair with a blow dryer until the pointer does not move anymore.
Make a mark on the wood with a paint pen and label it 0 percent.
This is the point at which there is no water vapor absorbed by the hair.
Put the hygrometer in a sealable plastic box with a wet rag.
After 10 minutes, make a tiny mark with a pencil at the pointer's location and put the hygrometer back in the box.
Check it again in another 10 minutes; continue this process until the pointer stops moving.
Mark that spot with a marker and label it 100 percent.
Divide the space between 0 percent and 100 percent into 10 spaces and label them 10 percent, 20 percent, 30 percent and so on.
You can also calibrate your hair hygrometer by setting it on the bathroom counter while you take a shower.
After marking the 100 percent humidity line, aim your hair dryer at the hair until the pointer stops moving and mark 0 percent. , Place your hygrometer on a shelf in the house or outside in an area that is protected from rain or snow.
As the hair dries or absorbs water, the pointer will move up or down to show the humidity of the air.
While the measurements are not especially accurate, they will give you an idea of the relative humidity in the air. -
Step 3: Cut a small triangle pointer.
-
Step 4: Tape the dime onto the tip of the pointer.
-
Step 5: Attach the hair to the pointer.
-
Step 6: Fasten the pointer to the wood block with a pin or nail.
-
Step 7: Hammer a second nail into the block about 1 inch (2.54 cm) from the top.
-
Step 8: Glue the other end of the hair to the nail at the top of the block.
-
Step 9: Calibrate the hygrometer.
-
Step 10: Check the position of the hygrometer pointer at different times of the day and record the results.
Detailed Guide
To make a hair hygrometer you will need 2-3 pieces of hair at least 12 inches long, a 9 inch by 4 inch wooden block or piece of cardboard, two pins or nails, rubbing alcohol, a dime, tape, a marker, a sheet of plastic transparency, a ruler, scissors, and a hair dryer.Most of these materials should be easily found around the home.
If you’re using nails, you will also need a hammer.
Parental supervision is advised during use of the hammer.
You can also substitute the transparency sheet for stiff cardstock or cardboard.
Mix 2 drops of alcohol and 8 drops of water.
Wipe the hairs with the mixture to remove oils or hair care products.
The cleaner the hair is, the more water it will be able to absorb.Keep the hair on a white piece of paper so you don’t lose it while you build the rest of the hygrometer.
Clean multiple strands of hair in case some break during the assembly process. , This pointer will be the arrow that allows you to measure relative humidity.
The pointer can be made out of stiff cardboard or the plastic transparency sheet.
Trace a triangle onto the sheet that has a base of 3 inches and sides that are about
2.5 inches tall.
Cut out the triangle using scissors.
Mark a spot about
1.5 centimeters from the base of the triangle in the center.
This will be the attachment point for the pointer. , Using a piece of tape, attach the dime close to the tip of the pointer.
It’s okay if the dime hangs off the edges a little bit.The dime serves as a weight, to keep the hair taut and straight.
If tape does not work, you can use a dab of hot glue.
Keep in mind, this is a slightly more permanent solution. , Glue the hair to the hygrometer pointer between the dime and the marking for the attachment point.
The hair should be perpendicular (make a 90 degree angle) to the pointer. , Using the mark you made earlier, poke a hole through the pointer with a pin or nail.
Hammer the pin/nail into the 9-inch-by-4-inch (22.86-cm-by-10.16-cm) wood block base about 6 3/4 inches (17.15 cm) from the top, with the pointer parallel to the ground (hanging horizontally).
Make sure the hole is large enough for the pointer to swivel around the nail. , Measure 1 inch from the top of the block and mark a point that is straight up from where the hair is positioned.
Hammer the nail into this spot on the block.
This second nail will be the anchor point for the hair. , Pull the piece of hair taut and wrap it around the nail at the top of the block.
Add a dab of glue to secure the hair in place.
You may need to hold the hair while the glue dries to make sure it is taut.
Make sure the hair is pulled tight and the tip of the pointer is horizontally straight/parallel to the ground.
Trim any extra hair. , Using a hair dryer and a wet rag, you can simulate the conditions of zero and one hundred percent humidity.
Dry the hair with a blow dryer until the pointer does not move anymore.
Make a mark on the wood with a paint pen and label it 0 percent.
This is the point at which there is no water vapor absorbed by the hair.
Put the hygrometer in a sealable plastic box with a wet rag.
After 10 minutes, make a tiny mark with a pencil at the pointer's location and put the hygrometer back in the box.
Check it again in another 10 minutes; continue this process until the pointer stops moving.
Mark that spot with a marker and label it 100 percent.
Divide the space between 0 percent and 100 percent into 10 spaces and label them 10 percent, 20 percent, 30 percent and so on.
You can also calibrate your hair hygrometer by setting it on the bathroom counter while you take a shower.
After marking the 100 percent humidity line, aim your hair dryer at the hair until the pointer stops moving and mark 0 percent. , Place your hygrometer on a shelf in the house or outside in an area that is protected from rain or snow.
As the hair dries or absorbs water, the pointer will move up or down to show the humidity of the air.
While the measurements are not especially accurate, they will give you an idea of the relative humidity in the air.
About the Author
Lori Castillo
Dedicated to helping readers learn new skills in lifestyle and beyond.
Rate This Guide
How helpful was this guide? Click to rate: