How to Make a Xylophone
Assemble the wood for the keys., Cut the keys roughly to size., Tune the keys., Find the position of the nodes on each bar., Drill 2 holes through each key where you marked the position of the nodes., Build the frame., Lay the keys across these 2...
Step-by-Step Guide
-
Step 1: Assemble the wood for the keys.
A one-octave xylophone will have 8 keys, with the root note of the scale appearing both at the lower and upper ends of the register.
The keys should be roughly 2 inches (5 cm) wide and 1 inch (2.5 cm) high.
Dimension lumber is widely available at hardware stores in roughly these dimensions.
Pine is an acceptable choice, although oak will yield a better tonal quality.
Professional quality xylophones have keys made of rosewood or padauk, but these woods are harder to find. -
Step 2: Cut the keys roughly to size.
A good approximation is to cut the lowest note to about 14 inches (35 cm) long and the highest note to about 10 inches (25 cm) long.
The keys in between should gradually bridge the gap between these 2 lengths.
With these lengths, the keys can be tuned easily to the C Major scale.
The exact length of each key is not important, as you will be trimming them down during the tuning process. , This is the most time-consuming step in the process.
Lay each key out on a soft surface (such as a towel) so that it can resonate.
Strike the key with a mallet and register the pitch on an electronic tuner.
If the pitch is too low, you can raise it by shaving or filing off the edges of the key to make it shorter.
If the pitch is too high, you can lower the pitch by carving out a curved gouge on the underside of the key.
The gouge should be centered on the bar, and should generally be kept within the middle third of the bar.
A rasp is the best tool for this, although a file or draw knife will also work.
Continue checking the pitch throughout the tuning process. , The nodes are the parts of the bar which will not vibrate when the bar resonates, and are located about 2/9 of the length of the bar in on each side.
To find their exact position, sprinkle salt on each key and strike it repeatedly with a mallet.
The salt will dance around on the bar and gather on the nodes (because there is no vibration there).
Mark this position with a pencil. , These holes should be centered across the width of the bar.
Make each hole slightly larger than the nail that will be used to secure the key to the frame, because the key must have room to move when it is struck, or it will not resonate very much. , You will need 4 pieces of wood for this, the dimensions of which do not matter much.
Lay the keys out from lowest to highest, with about
0.25 inches (6 mm) in between each key.
The lowest-pitched key should be on the left, with the highest-pitched key on the right.
The total width of your xylophone should be about 18 inches (45 cm).
Cut 2 pieces of your frame wood to this length, and then wrap them in a soft material (a towel or a worn-out piece of clothing will work).
The fabric will ensure that the keys can still resonate and will not be knocking loudly against the frame during play. , Drive nails through the pre-drilled holes in the keys and into the wood frame below.
Attach the 2 long pieces of wood to each other to keep the frame rigid.
Take the other 2 pieces of wood reserved for the frame and screw, nail or glue them across the 2 long pieces to form a 4-sided frame. , Go over the whole instrument with a piece of sandpaper to remove rough edges and improve the appearance. -
Step 3: Tune the keys.
-
Step 4: Find the position of the nodes on each bar.
-
Step 5: Drill 2 holes through each key where you marked the position of the nodes.
-
Step 6: Build the frame.
-
Step 7: Lay the keys across these 2 pieces of wood with the nodes of each key positioned directly over the frame.
-
Step 8: Sand the entire xylophone down.
Detailed Guide
A one-octave xylophone will have 8 keys, with the root note of the scale appearing both at the lower and upper ends of the register.
The keys should be roughly 2 inches (5 cm) wide and 1 inch (2.5 cm) high.
Dimension lumber is widely available at hardware stores in roughly these dimensions.
Pine is an acceptable choice, although oak will yield a better tonal quality.
Professional quality xylophones have keys made of rosewood or padauk, but these woods are harder to find.
A good approximation is to cut the lowest note to about 14 inches (35 cm) long and the highest note to about 10 inches (25 cm) long.
The keys in between should gradually bridge the gap between these 2 lengths.
With these lengths, the keys can be tuned easily to the C Major scale.
The exact length of each key is not important, as you will be trimming them down during the tuning process. , This is the most time-consuming step in the process.
Lay each key out on a soft surface (such as a towel) so that it can resonate.
Strike the key with a mallet and register the pitch on an electronic tuner.
If the pitch is too low, you can raise it by shaving or filing off the edges of the key to make it shorter.
If the pitch is too high, you can lower the pitch by carving out a curved gouge on the underside of the key.
The gouge should be centered on the bar, and should generally be kept within the middle third of the bar.
A rasp is the best tool for this, although a file or draw knife will also work.
Continue checking the pitch throughout the tuning process. , The nodes are the parts of the bar which will not vibrate when the bar resonates, and are located about 2/9 of the length of the bar in on each side.
To find their exact position, sprinkle salt on each key and strike it repeatedly with a mallet.
The salt will dance around on the bar and gather on the nodes (because there is no vibration there).
Mark this position with a pencil. , These holes should be centered across the width of the bar.
Make each hole slightly larger than the nail that will be used to secure the key to the frame, because the key must have room to move when it is struck, or it will not resonate very much. , You will need 4 pieces of wood for this, the dimensions of which do not matter much.
Lay the keys out from lowest to highest, with about
0.25 inches (6 mm) in between each key.
The lowest-pitched key should be on the left, with the highest-pitched key on the right.
The total width of your xylophone should be about 18 inches (45 cm).
Cut 2 pieces of your frame wood to this length, and then wrap them in a soft material (a towel or a worn-out piece of clothing will work).
The fabric will ensure that the keys can still resonate and will not be knocking loudly against the frame during play. , Drive nails through the pre-drilled holes in the keys and into the wood frame below.
Attach the 2 long pieces of wood to each other to keep the frame rigid.
Take the other 2 pieces of wood reserved for the frame and screw, nail or glue them across the 2 long pieces to form a 4-sided frame. , Go over the whole instrument with a piece of sandpaper to remove rough edges and improve the appearance.
About the Author
Danielle Garcia
Enthusiastic about teaching lifestyle techniques through clear, step-by-step guides.
Rate This Guide
How helpful was this guide? Click to rate: