How to Make Biofuel
Try your first batch of biodiesel with unused vegetable oil., Start with safety., Work in a well-ventilated room that is at least 70 degrees F (21 degrees C), and put down paper or plastic to plan ahead for spills. , Begin adding your components...
Step-by-Step Guide
-
Step 1: Try your first batch of biodiesel with unused vegetable oil.
Put your goggles on, work close to a sink and/or have a bucket of water ready for any body part that might come into contact with the chemicals. ,, Measure out
6.8 fl. oz. (200 milliliters) of methanol.
You can find methanol in gas tank antifreeze, available at hardware stores or auto part stores.
Pour it in a blender.
Use a scale that will accurately measure out grams to weigh out
3.5 grams of lye.
You can use Red Devil Lye Drain Cleaner (sodium hydroxide), but take the proper precautions because lye is poisonous.
Drain cleaners that are chlorine-based (calcium hypochlorite) will not work.
With the lid off, turn your blender on its slowest setting, and begin slowly adding the lye to the methanol inside.
This will create sodium methoxide, but take precaution that the mixture doesn't splatter all over.
It should take about two minutes for the lye to dissolve, so once it has, add
1.1 quart (1 liter) of vegetable oil. ,,, , Approximately 30 to 60 minutes after you pour it into your container, you will see layers appearing in your mixture.
The bottom layer is glycerin, and the lighter layer above it is bio-diesel. , Once the mixture has completely settled, you can pour off the biodiesel for use and discard the glycerin.
You can alternately use the glycerin for making soap. -
Step 2: Start with safety.
-
Step 3: Work in a well-ventilated room that is at least 70 degrees F (21 degrees C)
-
Step 4: and put down paper or plastic to plan ahead for spills.
-
Step 5: Begin adding your components.
-
Step 6: Blend your mixture for approximately 20 to 30 minutes on the slow setting.
-
Step 7: Pour your mixture
-
Step 8: once your blending is done
-
Step 9: in a wide-mouth jar
-
Step 10: Label it "poison."
-
Step 11: Check out the separation.
-
Step 12: Split your mix.
Detailed Guide
Put your goggles on, work close to a sink and/or have a bucket of water ready for any body part that might come into contact with the chemicals. ,, Measure out
6.8 fl. oz. (200 milliliters) of methanol.
You can find methanol in gas tank antifreeze, available at hardware stores or auto part stores.
Pour it in a blender.
Use a scale that will accurately measure out grams to weigh out
3.5 grams of lye.
You can use Red Devil Lye Drain Cleaner (sodium hydroxide), but take the proper precautions because lye is poisonous.
Drain cleaners that are chlorine-based (calcium hypochlorite) will not work.
With the lid off, turn your blender on its slowest setting, and begin slowly adding the lye to the methanol inside.
This will create sodium methoxide, but take precaution that the mixture doesn't splatter all over.
It should take about two minutes for the lye to dissolve, so once it has, add
1.1 quart (1 liter) of vegetable oil. ,,, , Approximately 30 to 60 minutes after you pour it into your container, you will see layers appearing in your mixture.
The bottom layer is glycerin, and the lighter layer above it is bio-diesel. , Once the mixture has completely settled, you can pour off the biodiesel for use and discard the glycerin.
You can alternately use the glycerin for making soap.
About the Author
Raymond White
Professional writer focused on creating easy-to-follow crafts tutorials.
Rate This Guide
How helpful was this guide? Click to rate: