How to Sharpen an Axe
Protect your hands and face., Clean and polish the head of the axe., Clamp the axe in a vice., Select a bastard file., Inspect the bevel of the axe., File with a steady motion into the blade., File repeatedly along a fan-shaped area., Switch to the...
Step-by-Step Guide
-
Step 1: Protect your hands and face.
Take these steps to avoid injury while sharpening an axe:
Wear thick leather gloves.
If your file does not have a finger guard, cut a slit in a piece of leather and fit it onto the file.Wear safety goggles to protect against metal dust.
A dust mask is optional for hand sharpening.
A respirator is recommended if you use power tools (but see Tips below.) -
Step 2: Clean and polish the head of the axe.
If there is any rust on your axe, clean it off with a rust eraser or steel wool.
Further polishing is mostly a matter of aesthetics, but not too difficult to accomplish:
Sand with coarse-grit aluminum oxide or silicon carbide sandpaper.
Rub the axe head with even pressure, moving from the poll (hammer end) to the blade.
Repeat with finer-grit sandpaper.
For excellent polish, repeat with extra-fine sandpaper and/or finish by applying a metal polish with a rag. (You may wait on this step until after sharpening.) , Clamp the axe horizontally for easier filing, or vertically for a more even edge (as this allows you to alternate sides).
If clamping horizontally, you may wish to tilt the axe to the angle of the bevel (usually 20 or 30º), so you can hold the file parallel to the table.
This is easier than judging the correct angle by sight. , A 10–12" (25–30cm) bastard mill file (coarse, single-cut, and slightly tapering) is the best choice for most axes.Shorter bastard files do not have the same density of teeth, so the length is not just a matter of convenience.You may use a smaller mill file for hatchets.
Clean clogged file teeth with a file card.
If the file is new, rub soft chalk over it to prevent clogging., Most axes have a slightly convex edge, about 20–30º.
Broader, more convex edges are more suitable for hardwood or frozen wood, as the curve pushes wood out of the way to protect the edge.
Carving axes have a straight, triangular point.Decide on your axe's shape before you begin sharpening, and keep a close eye on the edge as it develops.
In most cases, you'll want to match the existing bevel, following the curve of the blade to remove an even layer of metal., Hold the file handle in the palm of your dominant hand, with your thumb resting on top.
Curl the fingers of your other hand around the tip of the file.
Stand with one foot well in front of the other so you can use your shoulders to push the file.
To prevent the file from rocking back and forth, lead with your forward hand, then transfer smoothly to a push with the handle by the end of the stroke. , File into the edge in steady strokes.
Create a fan-shaped curve on the blade by varying the starting point of your stroke: start close to the edge at the top of the axe head, start about 2–3 inches (5–7.5 cm) when at the center, and curve back down to the edge again at the bottom of the axe head.
Do not make contact with the blade on the return stroke, as this will not sharpen the axe and may ruin your file.
Use a file card or wire brush to remove metal particles from the file when buildup occurs. , Once you feel a burr on the side you are not sharpening, turn the axe over and repeat the same steps on the other side of the edge.
Continue sharpening until the burr returns to the first side.
Switching sides more frequently throughout the process may result in a more even edge., Also called a sliding bevel, this is simply two hinged arms which you can tighten to any angle using a nut.
You can easily make this yourself out of scrap lumber.Set your bevel gauge to the desired angle using a protractor (usually 25º or so), then slot it over your axe edge.
If the angle is off, file further to remove material where needed. , Apply honing oil or sewing machine oil to the extreme edge, then rub the tip of a coarse whetstone along it in a circular motion.
Hone both sides alternately to move the burr from one side to the other, until it is nearly gone.
This burr is the "feather edge," or a very thin, bent end.
Run your finger along the edge to track its shape. "Water stones" made from clay or sandstone hone more quickly, but also wear down faster.
They require water instead of oil to float away the metal particles., To remove the feather edge completely, repeat the same honing process with a finer whetstone, or strop it away from the edge with a strap of leather.
A perfectly honed edge will not reflect any light, but a couple small nicks are not a big deal.
Most whetstones are two-sided, with a coarse and a fine side.
Examples with a finger groove in the middle are safer.
Repeat the honing (at least with the coarse stone) each time you're about to use the axe. , Wipe the blade with light machine oil, then rub in a mixture of beeswax and more oil.
This works best when the steel is warm. -
Step 3: Clamp the axe in a vice.
-
Step 4: Select a bastard file.
-
Step 5: Inspect the bevel of the axe.
-
Step 6: File with a steady motion into the blade.
-
Step 7: File repeatedly along a fan-shaped area.
-
Step 8: Switch to the other side when you can feel a burr.
-
Step 9: Measure the edge with a bevel gauge.
-
Step 10: Hone the edge with a coarse whetstone.
-
Step 11: Hone with a fine whetstone or a leather strop (optional).
-
Step 12: Protect the blade from rust.
Detailed Guide
Take these steps to avoid injury while sharpening an axe:
Wear thick leather gloves.
If your file does not have a finger guard, cut a slit in a piece of leather and fit it onto the file.Wear safety goggles to protect against metal dust.
A dust mask is optional for hand sharpening.
A respirator is recommended if you use power tools (but see Tips below.)
If there is any rust on your axe, clean it off with a rust eraser or steel wool.
Further polishing is mostly a matter of aesthetics, but not too difficult to accomplish:
Sand with coarse-grit aluminum oxide or silicon carbide sandpaper.
Rub the axe head with even pressure, moving from the poll (hammer end) to the blade.
Repeat with finer-grit sandpaper.
For excellent polish, repeat with extra-fine sandpaper and/or finish by applying a metal polish with a rag. (You may wait on this step until after sharpening.) , Clamp the axe horizontally for easier filing, or vertically for a more even edge (as this allows you to alternate sides).
If clamping horizontally, you may wish to tilt the axe to the angle of the bevel (usually 20 or 30º), so you can hold the file parallel to the table.
This is easier than judging the correct angle by sight. , A 10–12" (25–30cm) bastard mill file (coarse, single-cut, and slightly tapering) is the best choice for most axes.Shorter bastard files do not have the same density of teeth, so the length is not just a matter of convenience.You may use a smaller mill file for hatchets.
Clean clogged file teeth with a file card.
If the file is new, rub soft chalk over it to prevent clogging., Most axes have a slightly convex edge, about 20–30º.
Broader, more convex edges are more suitable for hardwood or frozen wood, as the curve pushes wood out of the way to protect the edge.
Carving axes have a straight, triangular point.Decide on your axe's shape before you begin sharpening, and keep a close eye on the edge as it develops.
In most cases, you'll want to match the existing bevel, following the curve of the blade to remove an even layer of metal., Hold the file handle in the palm of your dominant hand, with your thumb resting on top.
Curl the fingers of your other hand around the tip of the file.
Stand with one foot well in front of the other so you can use your shoulders to push the file.
To prevent the file from rocking back and forth, lead with your forward hand, then transfer smoothly to a push with the handle by the end of the stroke. , File into the edge in steady strokes.
Create a fan-shaped curve on the blade by varying the starting point of your stroke: start close to the edge at the top of the axe head, start about 2–3 inches (5–7.5 cm) when at the center, and curve back down to the edge again at the bottom of the axe head.
Do not make contact with the blade on the return stroke, as this will not sharpen the axe and may ruin your file.
Use a file card or wire brush to remove metal particles from the file when buildup occurs. , Once you feel a burr on the side you are not sharpening, turn the axe over and repeat the same steps on the other side of the edge.
Continue sharpening until the burr returns to the first side.
Switching sides more frequently throughout the process may result in a more even edge., Also called a sliding bevel, this is simply two hinged arms which you can tighten to any angle using a nut.
You can easily make this yourself out of scrap lumber.Set your bevel gauge to the desired angle using a protractor (usually 25º or so), then slot it over your axe edge.
If the angle is off, file further to remove material where needed. , Apply honing oil or sewing machine oil to the extreme edge, then rub the tip of a coarse whetstone along it in a circular motion.
Hone both sides alternately to move the burr from one side to the other, until it is nearly gone.
This burr is the "feather edge," or a very thin, bent end.
Run your finger along the edge to track its shape. "Water stones" made from clay or sandstone hone more quickly, but also wear down faster.
They require water instead of oil to float away the metal particles., To remove the feather edge completely, repeat the same honing process with a finer whetstone, or strop it away from the edge with a strap of leather.
A perfectly honed edge will not reflect any light, but a couple small nicks are not a big deal.
Most whetstones are two-sided, with a coarse and a fine side.
Examples with a finger groove in the middle are safer.
Repeat the honing (at least with the coarse stone) each time you're about to use the axe. , Wipe the blade with light machine oil, then rub in a mixture of beeswax and more oil.
This works best when the steel is warm.
About the Author
Amanda Thomas
Brings years of experience writing about home improvement and related subjects.
Rate This Guide
How helpful was this guide? Click to rate: