How to Patch a Bicycle Tube
Remove the wheel from the bike., Use tire levers to remove the tire., Locate the hole that's causing the leak., Mark the hole in the tube., Remove any foreign objects from the hole., If necessary, sand around the hole., Apply the patch., Know when...
Step-by-Step Guide
-
Step 1: Remove the wheel from the bike.
The first thing you should do for any flat is to remove the affected wheel.
Check the side of the wheel at the center of the spokes.
If you have a quick release (which looks like a small lever), flip it over and spin it counterclockwise to loosen.
If, on the other hand, you see a nut, you will need a wrench to loosen it.
After this, disconnect the brakes, move the brake pads out of the way, and remove the wheel.
If you're dealing with the rear flat, you'll also have the chain and gears to deal with.
Put slack in the chain by shifting into the smallest set of gears.
Loosen the quick release or unscrew the nut holding the wheel in place as normal.
If necessary, use your hands to pull back on the rear derailleur (the "arm" that the chain passes through containing the small pulleys) and/or maneuver the chain out of the way as you remove the wheel. -
Step 2: Use tire levers to remove the tire.
When you've successfully removed the flat wheel, take the outer tire off.
To do this, it can be helpful to use a sturdy prying tool.
Some bike shops will sell small, specially-designed tools called tire levers for this purpose.
Whether you use a tire lever or another tool, be careful not to pinch the tube and cause further damage as you work the tire away from the wheel.
You can leave one lip of the tire over the wheel rim when you're done to make re-installation easier.
To be clear, you don't specifically need tire levers here.
Any sort of prying tool that's strong enough for the task can work well.
Even unconventional solutions like screwdrivers or butter knives can do an admirable job., When the tire has been removed, pull the flat tube out from the tire and pinpoint the site of the puncture.
This can be done in several ways — a few are listed below:
Inflating the tube and visually checking the surface of the rubber for holes Listening for any hissing noises Feeling for streams of air Plunging the tube in a container of water and looking for bubbles , Flat-causing tire punctures can be surprisingly small.
Once you've found one, you don't want to lose it! Use a piece of chalk to make a "+" or "x" that intersects at the point of the puncture.
If you're using a glue-on patch, make your mark large so that you can still see it after you've smeared on the glue.
If you don't have chalk in your patch kit, a ballpoint pen or any other sort of writing utensil will do.
Chalk, however, is preferable because it's obviously easier to see white chalk on black rubber than blue or black pen. , Once you find the hole, carefully check to see if it was caused by a foreign object (like, for instance, a piece of broken glass, a sharp rock, etc.) or if it was a pinch flat (which will cause a puncture that looks like a snake bite but won't leave any foreign objects).Carefully check the inside rim of the tire for any protruding foreign objects and remove them if you find them.
You don't want the same object that caused the flat in the first place to re-puncture your tire because you didn't see it. , Different types of patches work in different ways — some require glue, while others do not, and some require sanding, while others can stick to the smooth rubber of the inner tube with no trouble.
Consult the directions included with your patch kit.
If you're directed to sand, use a small square of sandpaper to roughen up the area around the hole about as wide as the patch to be used.
Making the rubber a little less smooth can improve the sticking power of certain types of adhesives.
If you're unsure about whether or not to sand, lightly sanding is unlikely to hurt most patches' ability to stick to the tube, so you may want to sand just in case. , Next, stick your patch over the puncture hole according to any included directions.
Some patches require glue, while others can stick to the tire on their own — while the latter are more convenient, they can sometimes be less reliable.
General directions for both types of patches are below.
If the directions included with your patch differ from these, follow your instructions, rather than these directions.
Glue patches:
Apply the glue or rubber cement to the tube around the puncture hole, wait for the glue to set (many glues must dry until they are no longer tacky — consult any included directions for more information).
Finally, place the patch on the mostly-dry glue and hold firmly in place for a few minutes until it has sealed the leak.
Non-glue patches (sometimes called "self-adhesive" patches):
Simply remove the patch from its wrapper and lay the patch over the sanded puncture like a sticker.
Press down firmly to secure and, if necessary, wait until dry before riding. , In situations where you have a severely damaged tube, you may want to avoid wasting your patch by opting to simply replace the entire tube instead.
Tubes that have serious damage may not stay inflated long enough with the patch to make using it worth it, making full-on replacement a better choice.
Luckily, if you can get your hands on a new tube, the process of replacing the old one isn't hard.
Below are certain types of tube damage which may signal that it's better to forego a patch:
Multiple holes Large tears Air leaking even after patch is applied. , After your patch has had an opportunity to set, carefully feel around the inside of the tire for any protruding foreign objects, such as metal wire, which may have caused the puncture.
Take your repaired tube and carefully lay it in the hollow inside portion of the tire.
This is usually easiest if you inflate the tube slightly and slide one side in first, then work the rest in as necessary.
When you're done, double-check to make sure none of the tube is hanging out of the tire.
Make sure the inflation valve is pointing inward (away from the tire) when you lay the tube in the tire so that you can eventually inflate the tube. , Next, use your thumbs to slide the tire (which contains the partly-inflated tube) back onto the wheel.
Press the outer lips of the tire over the metal lip of the wheel so that they "lock" securely in place, being careful not to pinch the tube between the tire and the rim.
You may need to use your tire lever or prying tool to help you with the very last part of the tire, which can often be tricky to get over the lip of the wheel.
Note that some high-end bike tires are meant to only turn in one direction.
In this case, the intended direction of rotation will usually be indicated by small arrows on the walls of the tires.
Don't install the tire backwards! This can reduce the bike's performance and cause the tire to wear improperly.
Don’t forget to take the valve lid off when replacing the tube in the wheel.
The lidless inflation valve should slide through a circle-shaped hole in the wheel so that it can be easily accessed for pumping. , Next, grab an automatic or hand-operated pump and start putting some air in your tire.
Go gradually to allow the tube to shift and settle within the tire as it expands.
When fully-inflated, give the tire a squeeze, let the bike sit for a few minutes, then squeeze the tire again.
If it feels about as firm the second time as it did the first time, you're ready to ride! If you're worried about the tube settling improperly within the tube, feel free to inflate it before re-installing the tire on the wheel.
Note, however, that this can make the tire trickier to get back on. , You're nearly done — all you've got to do now is slide the wheel back on the bike, secure the quick release or screw on the wheel nut, re-connect the brakes, and you're good to go (unless you've been working with your rear wheel, in which case you'll also need to carefully loop the chain around the gears again).
Peddle cautiously until you feel confident that the patch won't immediately burst, then resume riding as you normally would! , Inner tube patches, while handy, aren't necessarily meant to last you forever.
These patches are great for getting you out of the woods when your tire blows and you have no replacement, but they don't offer a good long-term solution for a punctured inner tube.
While good-quality patches can approach the reliability of a brand-new inner tube, others can leak for a time immediately after patching or may offer only temporary protection.There's no substitute for an actual replacement, so you may want to at least shop for a new inner tube when you get the chance so that you can have one handy if you suffer another flat in the near future. -
Step 3: Locate the hole that's causing the leak.
-
Step 4: Mark the hole in the tube.
-
Step 5: Remove any foreign objects from the hole.
-
Step 6: If necessary
-
Step 7: sand around the hole.
-
Step 8: Apply the patch.
-
Step 9: Know when replacing the tube is a smarter choice.
-
Step 10: Replace the tube in the tire.
-
Step 11: Work the tire and tube back onto the wheel.
-
Step 12: Pump up the tube gradually to let the tube and tire settle into place.
-
Step 13: Replace the wheel on the bike.
-
Step 14: Consider buying a new tube when you can.
Detailed Guide
The first thing you should do for any flat is to remove the affected wheel.
Check the side of the wheel at the center of the spokes.
If you have a quick release (which looks like a small lever), flip it over and spin it counterclockwise to loosen.
If, on the other hand, you see a nut, you will need a wrench to loosen it.
After this, disconnect the brakes, move the brake pads out of the way, and remove the wheel.
If you're dealing with the rear flat, you'll also have the chain and gears to deal with.
Put slack in the chain by shifting into the smallest set of gears.
Loosen the quick release or unscrew the nut holding the wheel in place as normal.
If necessary, use your hands to pull back on the rear derailleur (the "arm" that the chain passes through containing the small pulleys) and/or maneuver the chain out of the way as you remove the wheel.
When you've successfully removed the flat wheel, take the outer tire off.
To do this, it can be helpful to use a sturdy prying tool.
Some bike shops will sell small, specially-designed tools called tire levers for this purpose.
Whether you use a tire lever or another tool, be careful not to pinch the tube and cause further damage as you work the tire away from the wheel.
You can leave one lip of the tire over the wheel rim when you're done to make re-installation easier.
To be clear, you don't specifically need tire levers here.
Any sort of prying tool that's strong enough for the task can work well.
Even unconventional solutions like screwdrivers or butter knives can do an admirable job., When the tire has been removed, pull the flat tube out from the tire and pinpoint the site of the puncture.
This can be done in several ways — a few are listed below:
Inflating the tube and visually checking the surface of the rubber for holes Listening for any hissing noises Feeling for streams of air Plunging the tube in a container of water and looking for bubbles , Flat-causing tire punctures can be surprisingly small.
Once you've found one, you don't want to lose it! Use a piece of chalk to make a "+" or "x" that intersects at the point of the puncture.
If you're using a glue-on patch, make your mark large so that you can still see it after you've smeared on the glue.
If you don't have chalk in your patch kit, a ballpoint pen or any other sort of writing utensil will do.
Chalk, however, is preferable because it's obviously easier to see white chalk on black rubber than blue or black pen. , Once you find the hole, carefully check to see if it was caused by a foreign object (like, for instance, a piece of broken glass, a sharp rock, etc.) or if it was a pinch flat (which will cause a puncture that looks like a snake bite but won't leave any foreign objects).Carefully check the inside rim of the tire for any protruding foreign objects and remove them if you find them.
You don't want the same object that caused the flat in the first place to re-puncture your tire because you didn't see it. , Different types of patches work in different ways — some require glue, while others do not, and some require sanding, while others can stick to the smooth rubber of the inner tube with no trouble.
Consult the directions included with your patch kit.
If you're directed to sand, use a small square of sandpaper to roughen up the area around the hole about as wide as the patch to be used.
Making the rubber a little less smooth can improve the sticking power of certain types of adhesives.
If you're unsure about whether or not to sand, lightly sanding is unlikely to hurt most patches' ability to stick to the tube, so you may want to sand just in case. , Next, stick your patch over the puncture hole according to any included directions.
Some patches require glue, while others can stick to the tire on their own — while the latter are more convenient, they can sometimes be less reliable.
General directions for both types of patches are below.
If the directions included with your patch differ from these, follow your instructions, rather than these directions.
Glue patches:
Apply the glue or rubber cement to the tube around the puncture hole, wait for the glue to set (many glues must dry until they are no longer tacky — consult any included directions for more information).
Finally, place the patch on the mostly-dry glue and hold firmly in place for a few minutes until it has sealed the leak.
Non-glue patches (sometimes called "self-adhesive" patches):
Simply remove the patch from its wrapper and lay the patch over the sanded puncture like a sticker.
Press down firmly to secure and, if necessary, wait until dry before riding. , In situations where you have a severely damaged tube, you may want to avoid wasting your patch by opting to simply replace the entire tube instead.
Tubes that have serious damage may not stay inflated long enough with the patch to make using it worth it, making full-on replacement a better choice.
Luckily, if you can get your hands on a new tube, the process of replacing the old one isn't hard.
Below are certain types of tube damage which may signal that it's better to forego a patch:
Multiple holes Large tears Air leaking even after patch is applied. , After your patch has had an opportunity to set, carefully feel around the inside of the tire for any protruding foreign objects, such as metal wire, which may have caused the puncture.
Take your repaired tube and carefully lay it in the hollow inside portion of the tire.
This is usually easiest if you inflate the tube slightly and slide one side in first, then work the rest in as necessary.
When you're done, double-check to make sure none of the tube is hanging out of the tire.
Make sure the inflation valve is pointing inward (away from the tire) when you lay the tube in the tire so that you can eventually inflate the tube. , Next, use your thumbs to slide the tire (which contains the partly-inflated tube) back onto the wheel.
Press the outer lips of the tire over the metal lip of the wheel so that they "lock" securely in place, being careful not to pinch the tube between the tire and the rim.
You may need to use your tire lever or prying tool to help you with the very last part of the tire, which can often be tricky to get over the lip of the wheel.
Note that some high-end bike tires are meant to only turn in one direction.
In this case, the intended direction of rotation will usually be indicated by small arrows on the walls of the tires.
Don't install the tire backwards! This can reduce the bike's performance and cause the tire to wear improperly.
Don’t forget to take the valve lid off when replacing the tube in the wheel.
The lidless inflation valve should slide through a circle-shaped hole in the wheel so that it can be easily accessed for pumping. , Next, grab an automatic or hand-operated pump and start putting some air in your tire.
Go gradually to allow the tube to shift and settle within the tire as it expands.
When fully-inflated, give the tire a squeeze, let the bike sit for a few minutes, then squeeze the tire again.
If it feels about as firm the second time as it did the first time, you're ready to ride! If you're worried about the tube settling improperly within the tube, feel free to inflate it before re-installing the tire on the wheel.
Note, however, that this can make the tire trickier to get back on. , You're nearly done — all you've got to do now is slide the wheel back on the bike, secure the quick release or screw on the wheel nut, re-connect the brakes, and you're good to go (unless you've been working with your rear wheel, in which case you'll also need to carefully loop the chain around the gears again).
Peddle cautiously until you feel confident that the patch won't immediately burst, then resume riding as you normally would! , Inner tube patches, while handy, aren't necessarily meant to last you forever.
These patches are great for getting you out of the woods when your tire blows and you have no replacement, but they don't offer a good long-term solution for a punctured inner tube.
While good-quality patches can approach the reliability of a brand-new inner tube, others can leak for a time immediately after patching or may offer only temporary protection.There's no substitute for an actual replacement, so you may want to at least shop for a new inner tube when you get the chance so that you can have one handy if you suffer another flat in the near future.
About the Author
Sophia Bell
Dedicated to helping readers learn new skills in lifestyle and beyond.
Rate This Guide
How helpful was this guide? Click to rate: