How to Skin a Snake
Remove the head, unless it is to be used for taxidermy purposes., Wash the outside of the snake thoroughly., Make an incision down the centerline of the belly, through the skin only, all the way from the stump where the head was attached to the base...
Step-by-Step Guide
-
Step 1: Remove the head
Most taxidermy projects require a different, more difficult method of skinning, but that method is not the focus of this article.
It is always best to work with a decapitated snake because even "dead" snakes have been known to strike, and the fangs are still quite dangerous.
By removing the head, you are removing all venom. -
Step 2: unless it is to be used for taxidermy purposes.
Soapy water or even plain water will work well.
Just make sure the soap is completely rinsed off of the snake. , On most snakes, there is a smaller belly scale covering the cloaca.
In the picture, this is the last cream-colored scale before the darker tail scales.
Simply split this up the middle just like the rest of the scales. , Be sure to separate the skin from the membrane underneath right at the head end.
You want clean skin with nothing attached to it.
The hide should be loose enough that it easily detaches from the carcass.
If the skin is a bit "tight"
a knife may be used to carefully free it in the tough places.
Peeling without the use of a knife can usually be accomplished all the way to the cloaca.
When the cloaca is reached, it is usually necessary to free it from the skin by cutting around the opening with the knife.
Continue skinning to the base of the rattle.
The attachments to the muscles that control the rattle generally make the hide harder to pull off.
A knife must be used in this area if the skin is too tight to peel off, as the skin is rather delicate in this section.
After the skin is completely freed from all but the rattle itself, cut through the tail as close to the base of the rattle as possible.
If the skin is to be saved with the rattle attached, it helps for the piece of flesh attached to the rattle to be small.
Don't fret too much about totally removing the flesh below the cloaca and above the rattles (basically the black and white banding on rattlesnakes).
It is almost impossible to completely remove the skin from the flesh in this area.
It will dry up easily.
Constrictor snakes such as bull and rat snakes cannot be "peeled".
Their skin is attached with many muscle attachments over the full length of the body.
Cutting through them is tedious as it is hard to get the skin free from the flesh and very easy to cut or tear the skin. , Care must be taken near the lower digestive region or the snake might excrete unappetizing substances on the meat. , Membrane and fat are often rather difficult to remove from the ribcage and backbone and can be cut free at this time. , -
Step 3: Wash the outside of the snake thoroughly.
-
Step 4: Make an incision down the centerline of the belly
-
Step 5: through the skin only
-
Step 6: all the way from the stump where the head was attached to the base of the rattle.
-
Step 7: Pull the skin from the flesh by hand
-
Step 8: again beginning at the head end
-
Step 9: using even tension on the skin to avoid tearing.
-
Step 10: Remove the viscera (innards) by hand
-
Step 11: starting at the head end
-
Step 12: using a scooping motion with the hand if the organs are difficult to remove.
-
Step 13: Rinse the now eviscerated and skinned snake in cool water to remove any excess blood or other undesirable substances.
-
Step 14: Cut the snake into segments that are the most convenient length for the desired method of cooking.
Detailed Guide
Most taxidermy projects require a different, more difficult method of skinning, but that method is not the focus of this article.
It is always best to work with a decapitated snake because even "dead" snakes have been known to strike, and the fangs are still quite dangerous.
By removing the head, you are removing all venom.
Soapy water or even plain water will work well.
Just make sure the soap is completely rinsed off of the snake. , On most snakes, there is a smaller belly scale covering the cloaca.
In the picture, this is the last cream-colored scale before the darker tail scales.
Simply split this up the middle just like the rest of the scales. , Be sure to separate the skin from the membrane underneath right at the head end.
You want clean skin with nothing attached to it.
The hide should be loose enough that it easily detaches from the carcass.
If the skin is a bit "tight"
a knife may be used to carefully free it in the tough places.
Peeling without the use of a knife can usually be accomplished all the way to the cloaca.
When the cloaca is reached, it is usually necessary to free it from the skin by cutting around the opening with the knife.
Continue skinning to the base of the rattle.
The attachments to the muscles that control the rattle generally make the hide harder to pull off.
A knife must be used in this area if the skin is too tight to peel off, as the skin is rather delicate in this section.
After the skin is completely freed from all but the rattle itself, cut through the tail as close to the base of the rattle as possible.
If the skin is to be saved with the rattle attached, it helps for the piece of flesh attached to the rattle to be small.
Don't fret too much about totally removing the flesh below the cloaca and above the rattles (basically the black and white banding on rattlesnakes).
It is almost impossible to completely remove the skin from the flesh in this area.
It will dry up easily.
Constrictor snakes such as bull and rat snakes cannot be "peeled".
Their skin is attached with many muscle attachments over the full length of the body.
Cutting through them is tedious as it is hard to get the skin free from the flesh and very easy to cut or tear the skin. , Care must be taken near the lower digestive region or the snake might excrete unappetizing substances on the meat. , Membrane and fat are often rather difficult to remove from the ribcage and backbone and can be cut free at this time. ,
About the Author
Maria Coleman
Specializes in breaking down complex home improvement topics into simple steps.
Rate This Guide
How helpful was this guide? Click to rate: