How to Drill a Lock
Examine the lock., Get the proper equipment., Attach a 1/8-inch (3mm) drill bit to your drill., Hammer a center punch at a point directly above the keyhole., Drill a hole through the lock cylinder through the guidance point., Go slowly., Switch to a...
Step-by-Step Guide
-
Step 1: Examine the lock.
Some tubular locks have a center pin made of hardened steel, while others have a ball bearing in the middle pin to prevent drilling.
In either case, drilling will prove ineffective and alternate lock-picking methods must be used.
If you are unsure if the lock is made with a hardened center pin, consult a local hardware store or locksmith and give them as much information as you have on the lock.
It's also important to double-check and make sure that you're working with a basic tumbler lock that you'll be able to knock out, and that there aren't other locking mechanisms on the door that'll keep you out.
Disable any alarms before attempting to drill a lock. -
Step 2: Get the proper equipment.
Since you're using a pretty primitive method to get the lock open, you won't need many sensitive tools to get the job done properly.
If you need to drill through a lock, you'll need:
A variable-speed power drill.
You want a well-maintained and powerful power drill that you'll be able to use to break the lock mechanism.
It would be very difficult to do this by hand.
Several sizes of drill bits.
There's no one drill-bit that'll be better than others, because you want to match it to the size of the lock.
Have a few on hand to experiment with. , For the most part, if it's going to work, you'll be able to get it started with a bit that's about an eighth of an inch wide.
If you don't have a bit that size, go with something in the neighborhood.
You want it relatively small, going through the mechanism, rather than drilling it out completely. , This will create a guidance point for drilling.
The point should be just below the shear line, the dividing line between the inner and outer cylinder of the lock, which will keep the drill bit on the center plug.
This should be high enough to effectively drill through the pin tumblers.
If you have difficulty finding the right place to sink your guidance hole, you can purchase a lock-drilling template.
Templates for a variety of locks are available at locksmith shops and hardware stores. , This destroys the pins inside the lock cylinder, allowing you to force the lock open.
Most locks have about five tumbler pins to drill through, although some have six or more.
You should feel more resistance as the drill bit encounters each pin, then a decrease in resistance as the bit cuts through the pin.
If the drill binds while drilling, you may need to put the drill in reverse and pull it out of the lock to draw out excess metal filings created by drilling through metal.
Lock-drilling templates for a variety of locks are offered for sale by locksmith businesses and hardware stores. , Feel the drill work and try not to work too quickly or press too hard, as this may jam or break the drill bit.
If you're having difficulty getting the bit to drill through the pins, you can stop at any time and lubricate the drill head with a little water or a synthetic oil lubricant to make the drilling easier.
Keep the drill level while drilling.
If you drill at an angle, you can accidentally drill through unnecessary metal and damage more of the lock. , After going through with your smaller bit, take it up a notch.
Attach a 1/4-inch (6.5mm) or larger drill bit to your drill, and go through the lock again with the larger bit to break up the pins more and open the lock. , Turn the locking mechanism in the same direction as you would with a key.
If you drilled correctly, the locking mechanism will turn, and you will gain entry to the previously locked door.
If the lock still will not turn, you may need to destroy the entire lock cylinder, as described below. , Some locks may be more complicated, meaning that you’ll have to drill through the entire lock assembly to open the locked area.
Switch to either a larger 3/4 inch (19 mm) drill bit or a specially made cylindrical tubular lock bit.
Tubular lock bits are generally
3.75 inches (9.53 cm) and similar to hole saws used to drill larger holes for installing locks in doors.
Drill through the entire mechanism.
This will destroy the entire lock.
You will then be able to access the previously locked area. -
Step 3: Attach a 1/8-inch (3mm) drill bit to your drill.
-
Step 4: Hammer a center punch at a point directly above the keyhole.
-
Step 5: Drill a hole through the lock cylinder through the guidance point.
-
Step 6: Go slowly.
-
Step 7: Switch to a slightly larger bit.
-
Step 8: Insert the blade of a flat-headed screwdriver into the lock head.
-
Step 9: Improvise if necessary.
Detailed Guide
Some tubular locks have a center pin made of hardened steel, while others have a ball bearing in the middle pin to prevent drilling.
In either case, drilling will prove ineffective and alternate lock-picking methods must be used.
If you are unsure if the lock is made with a hardened center pin, consult a local hardware store or locksmith and give them as much information as you have on the lock.
It's also important to double-check and make sure that you're working with a basic tumbler lock that you'll be able to knock out, and that there aren't other locking mechanisms on the door that'll keep you out.
Disable any alarms before attempting to drill a lock.
Since you're using a pretty primitive method to get the lock open, you won't need many sensitive tools to get the job done properly.
If you need to drill through a lock, you'll need:
A variable-speed power drill.
You want a well-maintained and powerful power drill that you'll be able to use to break the lock mechanism.
It would be very difficult to do this by hand.
Several sizes of drill bits.
There's no one drill-bit that'll be better than others, because you want to match it to the size of the lock.
Have a few on hand to experiment with. , For the most part, if it's going to work, you'll be able to get it started with a bit that's about an eighth of an inch wide.
If you don't have a bit that size, go with something in the neighborhood.
You want it relatively small, going through the mechanism, rather than drilling it out completely. , This will create a guidance point for drilling.
The point should be just below the shear line, the dividing line between the inner and outer cylinder of the lock, which will keep the drill bit on the center plug.
This should be high enough to effectively drill through the pin tumblers.
If you have difficulty finding the right place to sink your guidance hole, you can purchase a lock-drilling template.
Templates for a variety of locks are available at locksmith shops and hardware stores. , This destroys the pins inside the lock cylinder, allowing you to force the lock open.
Most locks have about five tumbler pins to drill through, although some have six or more.
You should feel more resistance as the drill bit encounters each pin, then a decrease in resistance as the bit cuts through the pin.
If the drill binds while drilling, you may need to put the drill in reverse and pull it out of the lock to draw out excess metal filings created by drilling through metal.
Lock-drilling templates for a variety of locks are offered for sale by locksmith businesses and hardware stores. , Feel the drill work and try not to work too quickly or press too hard, as this may jam or break the drill bit.
If you're having difficulty getting the bit to drill through the pins, you can stop at any time and lubricate the drill head with a little water or a synthetic oil lubricant to make the drilling easier.
Keep the drill level while drilling.
If you drill at an angle, you can accidentally drill through unnecessary metal and damage more of the lock. , After going through with your smaller bit, take it up a notch.
Attach a 1/4-inch (6.5mm) or larger drill bit to your drill, and go through the lock again with the larger bit to break up the pins more and open the lock. , Turn the locking mechanism in the same direction as you would with a key.
If you drilled correctly, the locking mechanism will turn, and you will gain entry to the previously locked door.
If the lock still will not turn, you may need to destroy the entire lock cylinder, as described below. , Some locks may be more complicated, meaning that you’ll have to drill through the entire lock assembly to open the locked area.
Switch to either a larger 3/4 inch (19 mm) drill bit or a specially made cylindrical tubular lock bit.
Tubular lock bits are generally
3.75 inches (9.53 cm) and similar to hole saws used to drill larger holes for installing locks in doors.
Drill through the entire mechanism.
This will destroy the entire lock.
You will then be able to access the previously locked area.
About the Author
Brian Cox
Dedicated to helping readers learn new skills in DIY projects and beyond.
Rate This Guide
How helpful was this guide? Click to rate: