How to Install A Car Radio Head Unit
Purchase all the necessary parts., Unplug your battery terminals., Take your car radio head unit out of the dash., Disconnect the car radio head unit wiring., Disconnect the antenna (usually a thick black wire but can also be a thick single wire)...
Step-by-Step Guide
-
Step 1: Purchase all the necessary parts.
Depending on whether you are upgrading to an aftermarket head unit or simply replacing the old one with another OEM (original equipment manufacturer) unit, you may have to have some additional hardware.
This could include things such as a dash kit, wiring harness, or antenna adapter. , You do not want the system to have live power while you are making your connections.
Turn the vehicle off and remove the cables from your battery. , A vehicle repair manual is highly recommended.
Also, the vehicle specific kit will contain detailed information on radio removal.
Removal of dashboard components may be required, and if you don't know how to remove the parts properly, permanent damage may occur.
In some cases, you may find two pairs of holes or slots on the left and right of the face of the radio.
These are called "key holes" and will require a special tool that can be purchased at most car audio stores or online to release the head unit. , With most harnesses, you will have to squeeze a clip or two for the harness to release from the radio.
Make sure that you examine the harness before pulling on it.
Be sure the harness you purchased fits the vehicle harness.
If it doesn't, take the radio to a car audio shop and have them locate the correct harness adapter. , Using a pair of pliers at the base of the wire may help.
Make sure you are pulling on the connector and not the wire as this will cause signal loss. , Use either the cage mount method (which involves using the metal sleeve that goes around your radio) or the ISO mount method which involves using the screws that were included with the radio.
When ISO Mounting a radio you use the factory brackets or brackets supplied with the new ISO Mount dash kit to Mount the radio.
Do not cut an ISO Mount kit and install the metal radio sleeve! If you cannot find the screws you can usually purchase them at your local car audio shop.
Make sure they do not exceed the maximum limits the manufacturer specifies or you will damage the radio. , Attach it to the harness you purchased making sure to match the colors exactly including the color of the stripe (i.e. white to white, black to black, orange with white stripe to orange with white stripe).
Strip approximately two inches insulation off of all of the wires and twist matching wires together.
This provides superior surface area connection to crimping and more flexibility than soldering.Cover the splice with electrical tape or a twist on wire nut If you have any trouble matching the wires, follow the steps provided with the wiring harness adapter.
The wires on the harness adapter and plug are usually color coded or tagged for easy identification and matching.
Some solder has lead in it, so avoid breathing in the fumes when you solder. , Connect the wiring harness you prepared and the antenna.
Make sure after you connect the wiring that the radio works properly.
This way you can find any wiring or radio problems before you reassemble everything.
Connect to the radio's wiring harness or harness adapter directly to the vehicle's wiring harness.
It is designed to simply plug in.
Connect the antenna wire to the back of the radio.
This rarely, but occasionally, requires an adapter. , This step will vary depending on what kind of head unit you have chosen, but instructions will be provided with your unit.
If the unit does not fit into the same space, it should have come with a modification kit to make it fit properly.
If your kit did not come with this, you should purchase one from your nearest car stereo retailer. , Now that your head unit is back in, you can put your interior back together.
Be sure to replace all clips and screws in the proper place and order.
Do not force anything that doesn't fit.
Consult your service manual if there are any portions of the dash that you are unsure how to install. , It is time to enjoy your new audio system! , If you have an amp in your system you want to make sure that you wire it in as well.
The remote turn-on wire is very important.
It tells your amp when the car is on or off and prevents the amp from draining your battery.
This wire will either plug directly into the back of your head unit, or need to be connected to the power supply to the head unit or another power supply., RCA cables are the insulated cables that transmit the sound signal from your head unit to the amp.
They should plug into the RCA ports on your head unit.
If they are not already run, be sure to run these cables on the opposite side of the car as the amp’s power wire to avoid signal disruption., It is important to make sure that your amp and head unit are working well together.
You need to reset the gain on your amp to compliment your new head unit. -
Step 2: Unplug your battery terminals.
-
Step 3: Take your car radio head unit out of the dash.
-
Step 4: Disconnect the car radio head unit wiring.
-
Step 5: Disconnect the antenna (usually a thick black wire but can also be a thick single wire).
-
Step 6: Assemble the dash kit according to the appropriate instructions.
-
Step 7: Wire up the new radio's harness.
-
Step 8: Connect the factory wiring.
-
Step 9: Put the new car radio head unit into the dash.
-
Step 10: Reassemble the dashboard.
-
Step 11: Reconnect battery terminals.
-
Step 12: Plug in the remote turn-on wire.
-
Step 13: Plug in the RCA cables.
-
Step 14: Set the gain on your amp.
Detailed Guide
Depending on whether you are upgrading to an aftermarket head unit or simply replacing the old one with another OEM (original equipment manufacturer) unit, you may have to have some additional hardware.
This could include things such as a dash kit, wiring harness, or antenna adapter. , You do not want the system to have live power while you are making your connections.
Turn the vehicle off and remove the cables from your battery. , A vehicle repair manual is highly recommended.
Also, the vehicle specific kit will contain detailed information on radio removal.
Removal of dashboard components may be required, and if you don't know how to remove the parts properly, permanent damage may occur.
In some cases, you may find two pairs of holes or slots on the left and right of the face of the radio.
These are called "key holes" and will require a special tool that can be purchased at most car audio stores or online to release the head unit. , With most harnesses, you will have to squeeze a clip or two for the harness to release from the radio.
Make sure that you examine the harness before pulling on it.
Be sure the harness you purchased fits the vehicle harness.
If it doesn't, take the radio to a car audio shop and have them locate the correct harness adapter. , Using a pair of pliers at the base of the wire may help.
Make sure you are pulling on the connector and not the wire as this will cause signal loss. , Use either the cage mount method (which involves using the metal sleeve that goes around your radio) or the ISO mount method which involves using the screws that were included with the radio.
When ISO Mounting a radio you use the factory brackets or brackets supplied with the new ISO Mount dash kit to Mount the radio.
Do not cut an ISO Mount kit and install the metal radio sleeve! If you cannot find the screws you can usually purchase them at your local car audio shop.
Make sure they do not exceed the maximum limits the manufacturer specifies or you will damage the radio. , Attach it to the harness you purchased making sure to match the colors exactly including the color of the stripe (i.e. white to white, black to black, orange with white stripe to orange with white stripe).
Strip approximately two inches insulation off of all of the wires and twist matching wires together.
This provides superior surface area connection to crimping and more flexibility than soldering.Cover the splice with electrical tape or a twist on wire nut If you have any trouble matching the wires, follow the steps provided with the wiring harness adapter.
The wires on the harness adapter and plug are usually color coded or tagged for easy identification and matching.
Some solder has lead in it, so avoid breathing in the fumes when you solder. , Connect the wiring harness you prepared and the antenna.
Make sure after you connect the wiring that the radio works properly.
This way you can find any wiring or radio problems before you reassemble everything.
Connect to the radio's wiring harness or harness adapter directly to the vehicle's wiring harness.
It is designed to simply plug in.
Connect the antenna wire to the back of the radio.
This rarely, but occasionally, requires an adapter. , This step will vary depending on what kind of head unit you have chosen, but instructions will be provided with your unit.
If the unit does not fit into the same space, it should have come with a modification kit to make it fit properly.
If your kit did not come with this, you should purchase one from your nearest car stereo retailer. , Now that your head unit is back in, you can put your interior back together.
Be sure to replace all clips and screws in the proper place and order.
Do not force anything that doesn't fit.
Consult your service manual if there are any portions of the dash that you are unsure how to install. , It is time to enjoy your new audio system! , If you have an amp in your system you want to make sure that you wire it in as well.
The remote turn-on wire is very important.
It tells your amp when the car is on or off and prevents the amp from draining your battery.
This wire will either plug directly into the back of your head unit, or need to be connected to the power supply to the head unit or another power supply., RCA cables are the insulated cables that transmit the sound signal from your head unit to the amp.
They should plug into the RCA ports on your head unit.
If they are not already run, be sure to run these cables on the opposite side of the car as the amp’s power wire to avoid signal disruption., It is important to make sure that your amp and head unit are working well together.
You need to reset the gain on your amp to compliment your new head unit.
About the Author
Alan Sanchez
Alan Sanchez specializes in marketing strategies and has been creating helpful content for over 2 years. Alan is committed to helping readers learn new skills and improve their lives.
Rate This Guide
How helpful was this guide? Click to rate: