How to Mount a Fireplace TV Bracket
Ensure suitability of the space., Purchase the appropriate fireplace wall mount., Make sure you have all hardware needed to secure your mount., Plan your mounting holes., Pre-drill the holes., Use the 4 3/8in lag bolts with washers to attach the...
Step-by-Step Guide
-
Step 1: Ensure suitability of the space.
To mount to your fireplace you will have to first make sure that your stone/brick is sturdy enough to hold the TV mount. -
Step 2: Purchase the appropriate fireplace wall mount.
Research options for your space; you can find ones of different sizes and options, including those that move down to a more comfortable viewing level and can extend out over the fireplace. , If mount does not include anchors, use one with that is 1/2″ diameter; thread: 3/8″-16; head width: 9/16″; washer OD: 1″ (drill size 1/2″).
You will have to figure out the correct length for yourself, based on your mounts and surface.
It's best to use at least 3 of these in the top row; these anchors are the ones that do most of the work.
To drill into the stone/brick you will probably need a special drill called a hammer drill, which you can rent from the hardware store along with the correct size bit.
Using the hammer drill is just as easy as using a regular drill. , Measure out where the bottom of the mount will be.
Use the mount as a template and mark the locations of the mounting holes.
The mounting holes need to be in the center of the studs; use a stud finder as needed.
Put the level on the top edge of the hook plate where the attach arms hook onto.
This edge should be level to help ensure a level TV. 2 mounting holes are needed in the top slots of the mount and 2 in the bottom slots. 2 mounting holes need to be on each side of the of the center of the mount and the center of gravity of the television. , Once you know your location, pre-drill the 4 mounting holes
2.5in deep using the 1/4in drill bit. , Tighten with a 9/16in box or socket wrench until the mount is firmly pressed against the wall.
A friend makes this much easier.
Do not over tighten. , Make sure it's secure, and then wire it up as needed. -
Step 3: Make sure you have all hardware needed to secure your mount.
-
Step 4: Plan your mounting holes.
-
Step 5: Pre-drill the holes.
-
Step 6: Use the 4 3/8in lag bolts with washers to attach the mount to the wall.
-
Step 7: Mount the TV onto the mounts.
Detailed Guide
To mount to your fireplace you will have to first make sure that your stone/brick is sturdy enough to hold the TV mount.
Research options for your space; you can find ones of different sizes and options, including those that move down to a more comfortable viewing level and can extend out over the fireplace. , If mount does not include anchors, use one with that is 1/2″ diameter; thread: 3/8″-16; head width: 9/16″; washer OD: 1″ (drill size 1/2″).
You will have to figure out the correct length for yourself, based on your mounts and surface.
It's best to use at least 3 of these in the top row; these anchors are the ones that do most of the work.
To drill into the stone/brick you will probably need a special drill called a hammer drill, which you can rent from the hardware store along with the correct size bit.
Using the hammer drill is just as easy as using a regular drill. , Measure out where the bottom of the mount will be.
Use the mount as a template and mark the locations of the mounting holes.
The mounting holes need to be in the center of the studs; use a stud finder as needed.
Put the level on the top edge of the hook plate where the attach arms hook onto.
This edge should be level to help ensure a level TV. 2 mounting holes are needed in the top slots of the mount and 2 in the bottom slots. 2 mounting holes need to be on each side of the of the center of the mount and the center of gravity of the television. , Once you know your location, pre-drill the 4 mounting holes
2.5in deep using the 1/4in drill bit. , Tighten with a 9/16in box or socket wrench until the mount is firmly pressed against the wall.
A friend makes this much easier.
Do not over tighten. , Make sure it's secure, and then wire it up as needed.
About the Author
Dennis Moore
Dennis Moore has dedicated 11 years to mastering educational content. As a content creator, Dennis focuses on providing actionable tips and step-by-step guides.
Rate This Guide
How helpful was this guide? Click to rate: